Leo/arcrun-rag-demo-knowledge
1
0
Fork 0
Code Issues Pull Requests Actions Packages Projects Releases Wiki Activity
Files
fcb9b114b0a347cab43e745fb1743c1a1e45d10e
arcrun-rag-demo-knowledge/docs/GSB-PLC報警表.md
T

2738 lines
69 KiB
Markdown
Raw Blame History

This file contains ambiguous Unicode characters
This file contains Unicode characters that might be confused with other characters. If you think that this is intentional, you can safely ignore this warning. Use the Escape button to reveal them.
 PLC 警报表
000 Circuit breaker
000 电路断路
- Overload of protective motor switch
- Motor defective
0
- 马达保护开关超载
- 马达损坏
- Check electrical cabinet
- Electrical motor check
- 检查电器箱
- 检查马达
001 Temperature drive / inverter
001 驱动器/换流器温度异常
- Overload of drives
- Filter of fan contaminated
- Fan in switch cabinet defective
- 驱动器超载
1
- 风扇滤网污染
- 电器箱风扇开关损坏
-Check motor temperature
- Change filter
- Check if the fan functions
- 检查马达温度
- 更换滤波器
- 检查风扇功能
002 Hydraulic pressure
002 油压异常
- No pressure build-up in hydraulic system
2 - Pressure loss - leaky pipe work
- Pressure switch defective
- 油压无压力
- 压力管线泄漏
- 压力开关损坏
- Visual inspection for oil loss
- Electrical connection of pressure switch
- 检查油料耗损
- 检查压力开关接线
003 Pneumatic pressure
气压系统故障
- Pressure loss - leaky pipe work
- Pressure switch defective
3
- 压力管件泄漏
- 压力开关损坏
- Visual inspection of pipe work
- Check the pressure switch
- 检查压力管
- 检查压力开关
004 PW 210 temperature max
004 PW210 温度到达极限
- Brake overload drives
4
- 驱动器煞车超载
- Optimize machine parameters
- Reduce feed rate
- 调整参数
- 降低进给
005 DA300 pressure
005 DA300 压力异常
- Pressure loss leaky pipe work
- Pressure switch defective
5 - 压力管件泄漏
- 压力开关损坏
- Change filter
- Visual inspection of pipe work
- Check the pressureswitch
- 更换滤材
- 检查压力管
- 检查压力开关
006 Power supply drives
006 电源供应器异常
- Supply and recovery unit not operational
- 供应及回升单元无动作
- Check supply and recovery unit
6
- Check connection PLC input
- Siemens SIMODRIVE 611 ER module (X111 72-73.1)
- Indramat Power Drive supply unit HVE (X7 3-4)
- 检查供应及回复单元
- 检查 PLC 输入点接线
- 西门子 SIMODRIVE 611 ER module (X111 72-73.1)
- Indramat 电源供应器 HVE (X7 3-4)
007 Release M07 for Txxx inactive
007 TXXX 不允许使用 M07
- Tool-specific release for M07 "Coolant, inside" in TOOL.T is
inactive.
- 刀具表中特定刀具 M07"中心出水"功能未启动。
- If the tool provides M07 "Coolant inside" the functioncan be
enabled via TOOL.T
7
PLC Status #Bit2.
PLC status for M07:
- %xxxxx0xx = M07 disabled
- %xxxxx1xx = M07 enabled
- 如果此刀具可使用 M07 中心出水功能，则在 TOOL.T 刀具表中
PLC Status #Bit2 中设定。
PLC Status 中 M07 设定:
- %XXXXX0XX = M07 取消
- %XXXXX1XX = M07 启动
008 Clamping mode not permitted(Tapping Cycle)
8 008 不可启动夹持模式(攻牙循环)
- A tapping cycle has been called while the tool axisis in clamping
mode.
- 在刀具轴夹持模式下呼叫攻牙循环
- Program M- or FN19 function to disable the clamping mode of
the tool axis before the cycle call.
e.g. Z-axis
FN 19: PLC =+99991 / +4
- 呼叫攻牙循环前使用 M 功能或 FN19 取消刀具轴夹持.
例如 Z 轴
FN 19: PLC =+99991 / +4
009 Machine guard is closed !
009 安全门关闭!
- Guards not opened
- Sensors defective
9
- 门锁未开
- 传感器损坏
- Open guards
- Check sensors
- 开门
- 检查传感器
010 Machine guard is open !
010 安全门开启!
- Guards not closed
- Sensors defective
10
- 门锁未关
- 传感器损坏
- Close guards
- Check sensors
- 关门
- 检查传感器
011 Coolant level low
11
011 冷却液水位过低
- Coolant level too low
- Level switch defective
- 冷却液液面过低
- 液位传感器故障
- Refill coolant
- Check the level switch
- 重新装填冷却液
- 检查液位传感器
012 Lubricating axes
轴润滑故障
- Lubrication cycle of axes not carried out correctly
- Pressure loss - leaky pipe work
- Pressure switch defective
12
- 轴向润滑循环未正确启动
- 压力管件泄漏
- 压力开关损坏
- Visual inspection for oil loss
- Electrical connection of pressure switch
- 检查油料损失
- 检查压力开关接线
013 Lubrication oil level low
013 润滑油油位过低
- Oil level of central lubrication system too low
- Level switch defective
13
- 中心润滑系统液面过低
- 液面开关损坏
- Refill oil
- Check the level switch
- 从新装填油料
- 检查液面开关
014 Servo drive release I32
014 伺服驱动器释放 I32
- Axes are ready to power on
- Servo drive release I32 is missing
- 轴向准备通电
- 伺服驱动器 I32 未正常作动
14 - Check wiring Interface NE2 MC42xx - X42/33
- 检查接线接口 NE2 MC42xx - X42/33
015 Servo drive release X150/X151 -> Axes group: %d
015 伺服驱动器释放 X150/X151 ->轴群组: %d
- Axes are ready to power on
- Servo drive release X151/X151 is missing
- 轴向准备通电
- 伺服驱动器 X150/X151 未正常作动
15 - Check wiring
Interface XX42x - X150/X151
- Check safety contactor combination, both channels should
beactive.
- 检查接线
界面 XX42x - X150/X151
- 检查是否安全接触，2 条电线通道应该要有作用
016 Servo drive release inverter UM
016 伺服驱动器模块 UM 未释放
- The axis inverter module (UM) is not READY, no messageto CC4xx
16
- 轴向模块(UM)未准备完成,没有讯号到 CC4xx
- Check PWM cable
- Pulse release (spindle or axis) not active - X71/X72
- 检查 PWM 电缆线
- 主轴没有动作-X71/X72
017 Central drive
017 中央驱动模式错误
- Several axes with central drive were started at the same time
- 多个轴向中心驱动同时启动
17 - Change NC program
- Each NC block must include only one axis with central drive.
- 检查 NC 程序
- 每一 NC 单节必须只能包含一个中心驱动轴
- 中心驱动轴轴向键不可同时按压
018 Positioning error TC magazine
018 刀库定位错误
- Tool magazine blocked or jammed
- Tool magazine loaded unevenly
- Axes optimization faulty
18
- 刀库卡住
- 刀具无法上刀
- 轴向未伺服调整
- Check tool distribution
- Optimize axes
- 检查刀具
- 轴向伺服调整
019 Axis motion from end position
019 轴向脱离极限位置
- One or more of the axes has triggered an over travel
-limit switch resulting in an Emergency stop
- 轴向已经将硬件极限开关紧急停止解除
- 由急停引起的限位报警
- (1) Select Manual operating mode
19
- (2) Close guard
- (3) Press "Retract" button
- (4) Switch control on
- (5) Clear error message Emergency stop (CE key)
- (1) 选择手动操作模式
- (2) 按压" 回复" 或 "Retract" 按钮
- (3) 启动
- (4) 清除紧急停止错误讯息(CE)键
- (5) 使用箭头键回归
020 Clamping/unclamping axes
-> axis %s (%d)
20 020 轴向夹持/松开
->轴 %s (%d)
- Sensors for clamping/releasing defective
- Pressure drop of pneumatic/hydraulic system
- [->] Additional note in PLC window: Identifies the axis
- 夹松讯号传感器损坏
- 油/空压压力不足
- [->] PLC 窗口附加讯息: 错误轴向
- Check sensors and re-adjust them if required
- Check compressed-air and hydraulic pressure
- 检查传感器或重新调整压力
- 检查空压或油压
021 Axis not in hirth position
-> axis %s (%d)
021 轴向不在固定分度位置
->轴 %s (%d)
- Axis not in Hirth position
- Axis movement was interrupted
21
- 轴向不是在分度位置
- 轴向移动中止
- Encoder/coupling loose
- Compensate reference mismatch via MP960
- Position the axis in manual operating mode on Hirth grid
- 编码器松脱
- MP960 原点位置补偿错误
- 重新以手动定位到正确位置
022 Nominal position not in hirth -> axis %s (%d)
022 指令位置不在正确分度位置->轴 %s (%d)
22
- Programmed target position not in Hirth grid
- 程序编辑位置不是分度位置
- Correct the NC program
- 补偿或修改 NC 程序
023 Drives not operational
23
-> axis %s (%d)
023 驱动器未启动
->轴 %s (%d)
- Axis drive not ready
- [->] Additional note in PLC window: Identifies the axis
- 轴向驱动未待命状态
- [ -> ] PLC 窗口附加讯息: 轴向错误
- Check hardware of axis drive; check diagnosis LED
- Switch unit on/off
- 利用灯号检查轴向驱动硬设备
- 硬件重新开关机
024 Power stage temperature max
-> axis %s (%d)
024 电源供应器温度过高
->轴 %s (%d)
- Overload of servo drive controller
24
- Filter contaminated
- 轴向伺服控制超载
- 过滤棉污染阻塞
- Reduce feed rate
- Check / change filter
- 降低进给
- 检查/ 更换过滤棉
025 Drives temperature max
-> axis %s (%d)
025 驱动器温度过高
->轴 %s (%d)
- Overload of servo drives
25
- 伺服驱动超载
- Check temperature of motors
- Reduce feed rate
- Switch unit on/off
- 检查马达温度
- 降低进给率
- 硬件重新开关机
026 Axes i2t pre-warning
-> axis %s (%d)
026 轴向 i2t 电流-温度预警
->轴 %s (%d)
26
- Overload of servo drives
- 伺服驱动超载
- Reduce feed rate
- Select smaller tools
- 降低进给率
- 选择较小刀具
027 Axes i2t limitation
-> axis %s (%d)
027 轴向 i2t 电流-温度预警极限
->轴 %s (%d)
27
- Overload of servo drives
- 伺服驱动超载
- Reduce feed rate
- Select smaller tools
- 降低进给率
- 选择较小刀具
028 Spindle not perational
028 主轴未运作
- Overload of spindle
- Spindle drive defective
- Spindle motor defective
- 主轴超载
28 - 主轴周边控制损坏
- 主轴马达损坏
- Reduce feed rate
- Check / change filter
- Check spindle motor
- Check cable / screwed onnection
- 降低进给率
- 检查周边控制
- 检查主轴马达
- 检查接线
029 Spindle nominal rpm
029 主轴转速差过大
- Nominal speed not reached or too low
- 无法到达指令速度或速度太低
- Reduce feed rate
29
- Select smaller tools
- Check speed with oscilloscope
- Optimize machine parameters
- 降低进给率
- 选择较小刀具
- 利用示波器检查速度
- 调整机械参数
030 Spindle stand still monitor
030 主轴定位异常
- Offset too high, spindle drifts
- Encoder or cable defective
- 主轴马达超载
- 主轴风扇污染
30
- Compensate offset (analog)
- Check encoder (oscilloscope)
- Check cable
- Optimize machine parameters
- 检查平移(模拟控制)
- 检查编码器(示波器)
- 检查接线
- 调整机械参数
031 Spindle I max
31
031 主轴电流过大
- Overload of spindle motor
- Spindle motor fan defective/not running
- 主轴马达超载
- 主轴风扇污染
- Reduce cutting values
- Check the fan
- 降低切削数值
- 清洁主轴马达风扇
032 Spindle T max (sensor Pt100)
032 主轴温度过高 (Pt100 温度传感器)
- Excessive temperature in spindle bearing
- Pt 100 temperature sensor defective
- Spindle motor fan defective
- 主轴培林温度过高
32
- Pt100 温度传感器损坏
- 主轴马达风扇损坏
- Reduce spindle speed
- Check Pt 100 temperature sensor
- Check spindle fan
- 降低主轴转数
- 检查 Pt100 温度传感器
- 检查主轴风扇
033 Spindle max torque
033 主轴到达最大扭力
- Maximum permissible torque exceeded
- 超过最大容许扭力
- Reduce feed rate
33
- Increase spindle speed
- Select smaller tools
- Optimize machine parameters
- 降低进给率
- 增加主轴转速
- 选择较小刀具
- 调整机械参数
034 Touch probe in spindle !
34
034 主轴有量测探针
- M03, M04, M05, M13, M14 only permissible if there is no touch
probe in the spindle. (no Probe in the PLC window)
- M03, M04, M05, M13, M14 只容许主轴没有量测探针才可执行。
(PLC 窗口中没有探针讯息)
- Change the tool (with PLC status %00000000) PLC status for
code of tool type
- 更换刀具 (PLC status %00000000) PLC status 对应刀具编码
- %00000000 = normal tool - %00000001 = touch probe
- %00000000 = 正常刀具 - %00000001 = 量测探针
035 Touch probe not in spindle !
035 主轴无量测探针
- Probe function selected but no touch probe in the spindle
("Probing" should flash in the PLC window)
- 已选择量测功能但主轴没有量测探针
35
(PLC 窗口中需有探针讯息)
- Change the touch probe PLC status for code of tool type
- %00000000 = normal tool
- %00000001 = touch probe
- 更换刀具 PLC status 对应刀具编码
- %00000000 = 正常刀具
- %00000001 = 量测探针
036 Spindle 1/2 activation
036 第 1/2 主轴启动异常
- The switching between spindle S1 and S2 was defective
36
- 在 S1 与 S2 主轴之间切换有问题
- Check MP settings (MP4020 bit 5)
- Check setting of MP3010/MP13010
- 检查 MP 的设定(MP4020 bit 5)
- MP3010/MP13010 是无法提供给 2 个主轴模式
037 Gear change
37 037 主轴换档异常
- The selected gear range cannot be coupled
- 选择的档位无法结合
- Check sensors for the gear ranges
- Clear error message (CE key) and retry
- 检查档位传感器
- 清除错误讯息后重新测试
038 Tool not clamped !
038 刀具未夹持!
- Tool change interrupted
- Tool unclamped
- Sensors or cables defective
38
- 换刀中断
- 刀具松刀
- 传感器或接线损坏
- Press the key "Clamp tool"
- Check the sensors
- 按压"夹刀"键
- 检查传感器
039 Tool unclamping, please !
039 请松刀!
- Call for Manual tool change
- Tool clamped
- 手动换刀的调用
- 刀具夹紧了
39 - Press the key "Unclamp tool"
- Remove the tool
- 按压键 "松刀"
- 取出刀具
040 Tool clamping, please !
040 请夹刀!
40
- Call for Manual tool change
- Tool unclamped
- 呼叫手动换刀
- 刀具松刀
- Press the key "Clamp tool"
- Insert the tool
- 按压"夹刀"键
- 插入刀具
041 TC quit, please !
041 请结束换刀!
- Call for Manual tool change
41
- Tool change carried out
- 呼叫手动换刀
- 换刀完成
- Press the key "Confirm tool change"
- 按压" 确认换刀"键
042 Close guard -> TC quit !
042 门关 -->换刀结束
- Call for Manual tool change
- Tool change carried out
42
- 呼叫手动换刀
- 换刀完成
- Close the guard
- Press the key "Confirm tool change"
- 关门
- 按压" 确认换刀"键
043 TC end -> NC start
043 换刀结束 -->按程序启动
- Call for a Manual tool in Auto mode
43
- Tool change carried out
- 呼叫手动换刀
- 换刀完成
- Press the NC start key to resume program run.
- 按压程序启动键
044 Check pocket table !
44 044 检查刀套表!
- Interruption during tool change
- It is possible that the pocket table does not correspond to the
loading of the magazine
- 换刀中断
- 刀套表与刀库对应可能错误
- Check/correct the pocket table
- 检查/更正刀套表
045 Correct tool in spindle ?
045 主轴刀号正确?
- The tool was unclamped without TOOL CALL
- 刀具在没有呼叫刀具松刀
- Check if the tool shown in the status is in the spindle and whether it
45 can be placed in the magazine
- NC start to carry out the tool change
- NC stop to interrupt the tool change
- 检查刀具状态是在主轴或刀库
- 按压程序启动键执行换刀
- 按压程序停止键结束换刀
046 Spindle is empty !
046 主轴空刀!
- There is no tool in the spindle
- Sensor defective
46
- 主轴无刀
- 传感器损坏
- Insert the tool
- Check the sensor
- 插入刀具
- 检查传感器
047 Spindle is not empty !
047 主轴有刀!
47
- There is a tool in the spindle although P0 in the pocket table is
empty - Sensor
defective
- 主轴有刀,但刀套表中 P0 无刀具
- 传感器损坏
- Remove the tool from the spindle
- Check the sensor
- 将刀具从主轴移除
- 检查传感器
048 Tool call T0 necessary !
048 需先呼叫 T0 刀
- Special function in case of tool change of tools withand without
magazine pocket
48
- Can be activated via MP
- 特殊换刀功能，换刀执行更换非刀套刀
- 可使用参数启动
- Change the NC program. First the tool must be removed from the
spindle (TOOL CALL 0) before a new tool is inserted.
- 更改 NC 程序，换刀前首先需移除主轴刀具
049 Tool not in tolerance
049 刀具尺寸超过误差
49
- Tolerance in tool table exceeded!
- 超过刀具表中设定之误差
- Check the tool
- 检查刀具
050 Tool life maximum
050 刀具最大寿命到达
- Tool life in tool table exceeded!
- 刀具使用时间超过刀具表设定寿命 !
- Check the tool
50 - Set the current tool life to 0
- 检查刀具
- 将目前刀具使用寿命设为 0
051 Tool change basic position
51
051 换刀基本位置异常
- Tool change interrupted
- Error during tool change
- 换刀中断
- 换刀中错误产生
- Move the tool change arm/magazine to their 'home' positions by
means of the service function (Help)inManual mode
- Test the inputs
- 进入手动模式利用除错模式(HELP)，移动至正确位置
- 测试 PLC I/O 输入点
052 Tool change timeout
052 换刀时间过长
- Timeout during tool change
- Interruption of tool change
52
- 换刀时间过长
- 中断换刀
- Press NC start key to continue the tool change
- Press internal stop soft key to stop the tool change
- 按压程序启动继续进行换刀
- 按压中断程序软键停止换刀
053 TC magazine guard open !
053 刀库门打开!
53
- Magazine guard open
- 刀库门开
- Close the tool magazine guard
- 关闭刀库门
054 TC magazine reference
054 刀库原点未复归
54
- Tool magazine has not been referenced
- 刀库未原点复归
- NC start to reference the tool magazine
- 按压程序启动执行原点复归
055 TC magazine timeout
55
055 刀库动作时间过长
- Timeout when positioning the toolmagazine
- Tool change interrupted
- 刀库定位时间过长
- 换刀中断
- Press NC start key to continue tool change
- Press internal stop soft key to interrupt tool change
- 按压程序启动继续执行换刀
- 按压程序中断终止换刀
056 TC magazine loading active !
056 刀库上下刀动作中!
- Loading of the tool magazine selected via soft key
56
- Tool magazine can be traversed and loaded
- 使用软键启动刀库上下刀功能
- 刀库可以移动及上下刀具
- Information only
- 仅供提示
057 TC magazine pocket not empty
057 刀套有刀
- Tool magazine not loaded correctly
- Erroneous entries in the pocket table
- Sensor defective
- 刀库上刀错误
57 - 刀套表输入错误
- 传感器损坏
- Load the tool magazine correctly - Check the
pocket table - Check the sensor
- 刀具重新上刀
- 检查刀套表
- 检查传感器
058 TC magazine pocket is empty
058 刀套无刀
58
- Tool magazine loaded incorrectly
- Erroneous entries in the pocket table
- Sensor defective
- 刀库上刀错误
- 刀套表输入错误
- 传感器损坏
- Load the tool magazine correctly
- Check the pocket table
- Check the sensor
- 刀具重新上刀
- 检查刀套表
- 检查传感器
059 Wrong tool in spindle
059 主轴刀具错误
- Block scan was stopped
- Different tools in status line and spindle
59 - 单节扫描停止
- 主轴刀状态或刀号错误
- In the MDI operating mode, insert the tool displayed in the status
line
- 在手动输入模式, 在状态中输入刀具显示
060 Alternating table timeout
060 交替工作台动作时间过长
- The alternating table cycle started with M61/M62 was
interrupted
60 - M61/M62 长工作台交换执行中断
- Press NC start key to continue the alternating table cycle
- Press internal stop soft key to interrupt the alternating table cycle
- 按压程序执行键继续执行长工作台交换
- 按压程序中断停止执行长工作台交换
061 Enable table 1 !
061 启动 1 号工作台 !
- M61 starts the NC processing on page 1 (left) but the release key
61 (probe) has not been pressed
- M61 已经启动但释放键尚未启动
- Press the key Alternating table mode on page 1 (left)
- 在第 1 页按压长工作台模式启动
062 Enable table 2 !
062 启动 2 号工作台 !
- M62 starts the NC processing on page 2 (right) but the release key
62 (probe) has not been pressed
- M62 已经启动但释放键尚未启动
- Press the key Alternating table mode on page 2 (right)
- 在第 2 页按压长工作台模式启动
063 Alternating table not active
063 交替工作台未启动
- M61 or M62 call the alternating table cycle although is has not
63
been activated (soft key or sensor dividing wall)
- M61 或 M62 已经执行但软键或分隔版传感器
- Activate the alternating operation by means of soft key or mounted
dividing wall
- 使用软键启动长工作台模式或安装分隔板
064 Alternating table X position
064 交替工作台 x 轴位置
- When trying to select the alternating table operation, the X axis
64 was in the range of the dividing wall
- 使用长工作台模式时,X 轴位置在分隔板位置
- Traverse the X axis from the middle in direction table 1/2
- X 轴位置需超过工作台一半
065 Pallet change basic position
065 交换工作台基本位置异常
- Pallet change interrupted
- Error during pallet change
- 交换工作台交换中断
65 - 交换工作台交换期间故障
- Move the pallet changer to its' 'home' position by means of the
service function (Help) in Manual mode.
- Test the inputs
- 在手动模式下,使交换工作台回到正常位置
- 测试输入点
066 Pallet change timeout
066 交换工作台交换时间过长
- Timeout during pallet change
- Interruption of pallet change
66
- 交换工作台交换时间过长
- 旋转工作台交换中中断
- Press NC start key to continue the pallet change
- Press internal stop soft key to stop the pallet change
- 压程序启动继续旋转工作台的交换
- 压内部停止软键去停止旋转工作台的交换
067 Pallet changer load guard open!
067 交换工作台的门打开!
67
- Pallet changer loading guard open
- 交换工作台的门打开
- Close the Pallet changer loading guard
- 关闭交换工作台的上下工件门
068 Workpiece not clamped !
068 工件未夹持!
- Pallet change interrupted
- Workiece unclamped
- Sensors or cables defective
68
- 交换工作台交换中断
- 工件松开
- 传感器或电线损坏
- Press the key "Workpiece clamping"
- Check the sensors
- 按压"工件夹紧"键
- 检查传感器
069 3D head timeout
069 3D 头动作时间过长
69 - Timeout during 3D head positioning
- Interruption of 3D head positioning
- 3D 头定位时间过长
- 中断 3D 头定位
- NC start key to continue the 3D head positioning
- Internal stop soft key to stop the 3D head positioning
- Service menu 3D head in manual mode
- 按压程序启动键继续 3D 头定位
- 按压中断内部程序执行中断 3D 头定位
- 手动模式中执行 3D 头服务模式故障排除
070 3D head set reference
070 3D 头设定原点
- 3D head reference settings not yet made
70 - 3D 头原点设定不是
- Set reference on service menu 3D head according to the axes
position
- 3D 头服务模式使用轴定位设定原点
071 3D head G range 1 necessary !
071 3D 头档位须回到低档!
71
- 3D head positioning is possible only in gear range 1
- 3D 头定位必须在低档位
- Select spindle rpm on 1st gear range TOOL CALL Sxxx
- 适用 Tool call SXXX 定义主轴转速在低档位
072 Insert spindle S2
072 装入 S2 主轴
72
- M42 has been called to insert spindle S2
- M42 被执行以装入 S2
- Insert spindle S2 and press NC start key to continue
- 装入主轴 S2 并按 NC start 键继续
073 Remove spindle S2
073 移除 S2 主轴
73
- M41 has been called to remove spindle S2
- M41 被执行以移除主轴 S2
- Remove spindle S2 and press NC start key to continue
- 移除主轴 S2 并按 NC start 键继续
074 Tool Call from wrong magazine
74
074 从错误的刀库呼叫刀具
- A Tool has been called, which cannot be changed into the
current spindle S1/S2.
- 刀具呼叫无法从现有主轴 S1/S2 被更换.
- Change NC program.
- 修改 NC 程序.
075 预留
75 Reserved
076 PLC 9255 - Line: %d - W1022: %d
File: %s
76 PLC 模块 %d - 行号: %d
档案: %s
- PLC module 9255 has been caused an error by reading a able
- Line: xxx -> Line number of the table the error occurred
76
- W1022: xxx -> error recognition
- PLC 模块 9255 表格读取错误
- 行号: XXX
-->表格中此行发生错误
- Please see also module description
- Please contact the OEM
- 请参考模块说明
- 请联络机械制造商
077 Commissioning active
077 机械调整模式启动中
- The option "commissioning" has been set in the configuration of
machine parameter/MP Config. Several monitoring functions are
77
disabled. - - Information only
- 在机械参数/ MP Config 中此选项"commissioning" 已经设定.多项监
控功能已经取消.
- 仅为讯息提式
- When the machine is delivered (factory default setting) the option
should be switched off after the commissioning has been ompleted.
- 出厂前机台调整完成后须将此功能关闭
078 Function not active
078 功能未启动
- Function not executable
78 - Option not active
- 此功能不能执行 - 此功能未开启
- Information only
- 只是讯息
079 Marker one/zero modified
079 Marker 1/0 已修改
79
- Error in PLC program
- PLC 程序错误
- Please inform OEM
- 请通知 OEM 厂
080 Value not permissible
080 输入值无法写入
- Function can not be activated because the values are not in the
80
permissible data range.
- 此功能无法启动,因为此值不是在允许的范围内.
- Check FN19, M-function and modify values.
- Check values for temperature- and axis-compensation
- 检查 FN19,M-功能和修改值的大小
081 Monitoring working area off !
081 工作区域监控取消!
- CAUTION !
- Axis may collide
81 - Monitoring working area has been switched off by soft key or M32.
- 注意
-轴向可能发生碰撞
- 监视工作区已经藉由功能键或 M32 被关闭
- Information only - 仅供提示讯息
082 Protected working area !
82 082 被保护的工作区域 !
- Axes are near to a collision point.
- In automatic mode axes are stopped, if the distance to go exceeds
a collision point.
- 轴向在可能碰撞区域
- 如果移动位在碰撞区域，在自动模式轴向停止
- Information only
- 仅供提示讯息
083 Emergency stop after END PGM
083 程序结束后紧急停止
- The switching off of the machine after the next END PGM block was
83
activated via user parameters
- 程序执行完毕后机台自动关闭
- 此功能由用户参数启动
- Information only
- 仅供提示讯息
084 Reference necessary
084 需做原点复归
84
- The reference operating mode is necessary to carry outFunction
- 需执行原点复归
- Select the operating mode Reference via soft key
- 手动模式中启动原点复归软键
085 Hirth axis initialize
085 离合轴初始化
- There has been an actual to nominal value transfer for an axis
which should keep the nominal value as actual (e.g. hirth axes)
- It is no longer guaranteed that the kinematics can be calculated
85
correctly.
- 呼叫一把不能交换之刀具
- 例主轴 S1 启动 -> CR 在位置供给 HSC 主轴 S2
- After a positioning the initialisation of the hirth axes will be
executed.
- 修改表之位置
- 修改 CR Aufruf
- 修改 NC 程序
086 Temperature compensation
086 温度补偿
- Error occurred with temperature compensation by means of Pt100
sensors
- 使用 PT100 传感器执行温度补偿发生错误
86 - Observe the information regarding the error reason in the small
PLC window
- 从 PLC 小窗口中检查错误讯息
087 PLC stack not empty !
087 PLC 推迭未清空 !
- Debug note for PLC programmers
87
- Data was pushed onto the stack and not pulled off.
- PLC 编辑，除错提示
- 档案放入堆栈后未提出
- Change the PLC program
- 修改 PLC 程序
088 I'm reading MP's ...
088 参数读取中.....
- With the first PLC scan or after changes the machine parameters
are read in order to adapt the PLC functions
88 - Only after termination of this process can the machine be started
- 机械参数修改后第 1 次 PLC 扫描，以配合 PLC 功能
- 需结束此程序后机械才可启动
- Information only
- 仅供提示讯息
089 M00 programmed stop
089 M00 程序中断
- Program interruption caused by M00
89 - Press NC start to continue
- 程序使用 M00 中断
- 按压程序启动后继续
- Information only
-仅供提示讯息
090 M01 conditional stop
090 M01 选择性停止
- Program interruption caused by M01
90 - Press NC start to continue
- 使用 M01 中断程序 - 按压程序启动继续加工
- Information only
- 仅供提示讯息
091 M03/M04 or M19/M20 necessary
091 需启动 M03/M04 或 M19/M20
- To move axes at machining feed rate, one of the mentioned M
commands must be active
- M31 switches off the function temporarily until the next END PGM
- Function can be deselected permanently via MP
91 - 使用加工进给移动轴向，上述提到之 M 功能需启动
- 使用 M31 暂时关闭此功能，直到下次程序结束
- 此功能可使用机械参数启动或取消
- Press NC stop / TNC stop
- Correct the NC program
- 按压程序停止及程序内部停止
- 修改 NC 程序
092 M function not used
092 M 功能未使用
- Programmed M command is not supported by the PLC program
92
- 编辑之 M 功能不支持 PLC 程序
- Press NC stop / TNC stop
- Correct NC program
- 按压程序停止及控制器停止
- 修改 NC 程序
093 Feed/Rapid feed pot = 0% !
93
093 程序/快速进给旋钮为 0% !
- Program start with turned off feed/rapid feed rate potentiometer.
- 程序启动，进给旋钮关闭
- Increase the feed rate on the corresponding potentiometer
- 旋转旋钮增加进给
094 Function ok !
094 功能正常 !
- The active step of a HELP file was carried out successfully
94
- All relevant sensors O.K.
- 除错模式(HELP FILE)步骤执行完成
- 传感器状态正确
- Information only
- 仅供提示讯息
095 Check machine parameter !
095 检查机械参数!
- The machine parameter setting is not supported by the PLC
program
95
- 机械参数设定不支持 PLC 程序
- Change the machine parameter
- Observe the information regarding the error reason in the small
PLC window
- 更改机械参数
- 从 PLC 小窗口中检查错误讯息
096 Simulation Maschine aktiv
-> For testing only!
096 仿真模式启动中
-->仅供测试使用!
- Simulation of machine function activated by means of control test
unit, although due to the I/O assignment a real machine can be
96 presumed
- 使用控制器测试平台除错功能
- 与实际机台 I/O 配置可能不同
- OEM.CFG:
DEFINE CFG_Simulation = "inactive"
- 编辑 config.def
DEFINE CFG_Simulation = "inactive"
097 Submit/Spawn queue full
097 Submit/Spawn 队列已满
97
- More than 8 jobs have been sent to the submit orspawn queue
- 超过 8 个任务送给了 submit 或 spawn 队列
- Please contact the OEM
- 请联系 OEM
098 TNC programming station
098 TNC 程序仿真器
- TNC programming station selected (MP7210).
- Axes and spindle are not controlled.
- Caution ! If PLC is active (MP7210=1), machine functions on
simulated axes and spindle positions can be started.
- 选择 TNC 仿真器 (MP7210).
- 不能控制伺服轴与主轴
- 注意 ! 若 PLC 启动选择 (MP7210=1), 仿真轴与主轴位置之机械功能
可以启动
Special functions key combination TExx0
- Keys [Ctrl] + S -> NC start
- Keys [Ctrl] + X-> NC stop
-Keys [Ctrl] + Cursor up-> axes plus
98
- Keys [Ctrl] + Cursor down-> axes minus
- Keys [Alt] + X-> Emergency stop PC keyboard or mouse support
possible -
Keys [Shift]+[Ctrl]+[Alt]+1 -> vertical soft key 1 ...
- Keys [Shift]+[Ctrl]+[Alt]+6 -> vertical soft key 6
特殊功能键结合 TExx0
- 按键 [Ctrl] + S -> NC start
- 按键 [Ctrl] + X -> NC stop
- 按键 [Ctrl] + Cursor up ->正轴向
- 按键 [Ctrl] + Cursor down ->负轴向
- 按键 [Alt] + X ->紧急停止计算机键盘或鼠标可以支持
- 按键 [Shift]+[Ctrl]+[Alt]+1 ->虚拟软键 1 ...
- 按键 [Shift]+[Ctrl]+[Alt]+6 ->虚拟软键 6
099 Message in PLC window
099 有讯息在 PLC 窗口中
- Further notes are displayed in the PLC window
99
- 进一步讯息显示在 PLC 窗口
- Press CE to clear the display
- Press CE to display the next information (if available)
- 按压 CE 清除显示
- 按压 CE 显示另一个讯息(如果有其他讯息)
100 Logbook writing
100 历程数据写入异常
- Data cannot be written to logbook
100
- 数据无法写入历程纪录
- Too many submit jobs active
- Create data buffer in PLC memory (PLC application)
- 太多 submit jobs 启动
- PLC 内存中产生数据缓冲区(PLC 开发)
101 PLC Module %d(1) - W1022: %d %s
101 PLC 模块 %d(1) - W1022: %d %s
- PLC module 9xxx was not executed successfully.
- (1) -> the first PLC module error during the PLC cycle
- PLC 模块 9XXX，产生错误
101
- (1) -->在 PLC 周期间 , 第 1 个 PLC 模块产生错误
- Additional information in line 2
- Please see also module description
- Please contact the OEM
- 进一步讯息参考第二行
- 请参考模块描述
- 传送讯息至 OEM 厂
102 PLC Module %d(2) - W1022: %d %s
102 PLC 模块 %d(2) - W1022: %d %s
102 - PLC module 9xxx was not executed successfully.
- (2) -> the second PLC module error during the PLC cycle
- PLC 模块 9XXX，产生错误
- (2) -->在 PLC 周期间 , 第 2 个 PLC 模块产生错误
- Additional information in line 2
- Please see also module description
- Please contact the OEM
- 进一步讯息参考第二行
- 请参考模块描述
- 传送讯息至 OEM 厂
103 PLC Module %d(3) - W1022: %d %s
103 PLC 模块 %d(3) - W1022: %d %s
- PLC module 9xxx was not executed successfully.
- (3) -> the third PLC module error during the PLC cycle
- PLC 模块 9XXX，产生错误
103
- (3)-->在 PLC 周期间 , 第 3 个 PLC 模块产生错误
- Additional information in line 2
- Please see also module description
- Please contact the OEM
- 进一步讯息参考第二行
- 请参考模块描述
- 传送讯息至 OEM 厂
104 PLC Module %d(4) - W1022: %d %s
104 PLC 模块 %d(4) - W1022: %d %s
- PLC module 9xxx was not executed successfully.
- (4) -> the fourth PLC module error during the PLC cycle
- PLC 模块 9XXX，产生错误
104
- (4) -->在 PLC 周期间 , 第 4 个 PLC 模块产生错误
- Additional information in line 2
- Please see also module description
- Please contact the OEM
- 进一步讯息参考第二行
- 请参考模块描述
- 传送讯息至 OEM 厂
105 Check MP data table
105 105 检查 MP date 表
- Error during reading PLC:\MP\MP_data.tab
- 读取档案期间错误 PLC:\MP\MP_data.tab
- Check values in PLC:\MP\MP_data.tab
- If necessary update file from existing backup
- 检查档案的值在 PLC:\MP\MP_data.tab
- 可以从备份文件中作档案的更新
106 Check MP Config Table
106 检查 MP config 表
- Error during reading PLC:\MP\MP_config.tab
106
- 读取档案期间错误 PLC:\MP\MP_config.tab
- Check values in PLC:\MP\MP_config.tab
- If necessary update file from existing backup
- 检查档案的值在 PLC:\MP\MP_config.tab
- 可以从备份文件中作档案的更新
107 RSxxx data transfer PLC
107 RSxxx 数据传送到 PLC 异常
- Attempt to synchronize data transmission on serial interface
- 在串行接口,同步数据的传送失败
107
- Switch on receiver
- Check machine parameter MP5xxx of master and slave
- Check cableconnection
- 开启接收端
- 检查机械参数 MP5xxx
- 检查传输线的接线
108 RSxxx buffer overflow
108 RSxxx 缓冲储存区溢位
108
- Internal message
- 内部的讯息
- Please contact the OEM
- 传送讯息至 OEM 厂
109 RSxxx transmit error
109 109 RS xxx 传输错误
- Error on serial interface RSxxx detected
- 串行接口 RSxxx 检查发现错误
- Check the cable connection
- Press CE key and try to reconnect
- 检查传输线的接线
- 请按压 CE 键且试着从新联机
110 RSxxx receive error
110 RSxxx 接收错误
- Error on serial interface RSxxx detected
110
- 串行接口 RSxxx 检查发现错误
- Check the cable connection
- Press CE key and try to reconnect
- 检查传输线的接线
- 请按压 CE 键且试着从新联机
111 RSxxx not operational
111 RSxxx 无法操作
- Error on serial interface RSxxx detected
111
- 串行接口 RSxxx 检查发现错误
- Check the cable connection
- Press CE key and try to reconnect
- 检查传输线的接线
- 请按压 CE 键且试着从新联机
112 Table editor blocked
112 表的编辑被锁住
- There is a table already open. The MP- or Config file cannot be
edited.
- In operating mode "Traverse reference points" it is not possible to
112
start the table editor.
- 表已被开启. MP 或 Config 档案无法被编辑.
- 在"原点复归" 模式不能编辑表.
- Please close the table (e.g. Tool table) and retry.
- Please change to mode "Manual operation".
- 请关闭表 (例刀具表) 并重试.
- 请切换至 "手动操作"模式.
113 Warning! DCM not yet active
Permit positioning of axis %d-%s
113 警告！DCM 未启动
容许定位轴向向 %d-%s
- DCM only becomes active after referencing all axes.
- To prevent the danger of a collision, the operator must check the
current axes positions.
- DCM 仅在所有轴向回原点后启动.
- To 为防止碰撞的危险, 操作者务必检查现有轴向之位置.
- NC Start key:
Movement to a safe position is executed.
Subsequently, the reference run of the following axes is started
automatically (option).
- NC Stop/Axis Direction keys:
Automatic reference-run is aborted.
The reference run must be performed manually (axis direction
113 keys).
- NC Start 按键:
执行移动至安全位置.
其次, 以下轴向之原点复归将自动执行 (选配).
- NC Stop/Axis 方向按键:
自动原点复归被取消.
原点复归必须手动执行 (轴方向按键).
114 Reference NC start disabled!
-> Use axis direction keys
114 程序启动键执行原点复归取消
-->使用轴向移动键
114
- Automatic referencing with NC start was aborted.
- Automatic referencing cannot be ensured
(nonvolatile RAM area not yet initialized).
- 程序启动键执行自动原点复归被取消.
- 自动原点复归未被确认
(非挥发性的内存区域未初始化).
- The reference run must be performed manually
(axis direction keys).
- 原点复归必须手动执行
(轴方向按键).
115 Reference timeout axis %d-%s
115 原点复归逾时 %d-%轴
- Axis not yet reached safe position
- 轴向未到达安全位置
- NC Start key:
The traverse to a safe position will be re-started. Subsequently, the
reference run of the axes is startedautomatically (option).
115 - NC Stop/Axis Direction keys:Automatic reference-run is aborted.
The reference run must be performed manually
(axis direction keys).
- NC Start 按键:
移动至安全位置将再开始一次.随后, 原点复归将自动开始 (选配).
- NC Stop/Axis 方向按键:
自动原点复归被取消.
原点复归必须手动执行 (轴方向按键).
116 Plug/unplug additional axis
116 插入/拔除附加轴向
116
- To plug or unplug an additional axis the machine mustbe off.
- 插入或拔除一附加轴向必须将机器关闭.
- Power off the machine !
- 将机器关闭 !
117 Axes compensation changed!
117 变更轴向补偿值!
117 - Factor for linear axes compensation X, Y or Z has been changed.
- X, Y 或 Z 之轴向线性补偿因子已经变更
- only message -仅供提示讯息
118 IPC 61x0 clock monitoring
118 118 IPC 61X0 时序监控错误
- IPC61x0 interface is faultily
(Watchdog)
- Operation via IPC has been deactivated
- IPC61X0 接口错误 (监控功能)
- 关闭由 IPC 操作机台功能
- Try to reconnect by key <Connect>
- Check ethernet interface
- 请尝试由按键<Connect>重新链接
- 检查网络联机设定
119 Operation mode 2
119 第二操作模式
- Information only
119
- 仅为讯息提示
- Spindle speed max = S800
- Axes feed max = F2000
- 主轴最高转速 = S800
- 轴向进给 = F2000
120 Operation mode 3
120 第三操作模式
- Information only
120
- 仅为讯息提示
- Spindle speed max = S5000
- Axes feed max = F5000
- 主轴最高转速 = S5000
- 轴向进给 = F5000
121 Operation mode 4
121 第四操作模式
- Information only
121
- 仅为讯息提示
- Spindle speed max = S5000
- Axes feed max = F5000
- 主轴最高转速 = S5000
- 轴向进给 = F5000
122 EMERGENCY STOP test required
122
-> Time remaining: %s h
122 需进行紧急停止测试
-->剩余时间: %s h
- The EMERGENCY STOP test of the equipment needs to be
repeated.
- No new NC program can be started.(NC start lock)
- A brake test is performed together with the EMERGENCY STOP test.
- 设备需重复进行紧急停止测试
- 未测试完成前,程序无法启动
- 紧急停止测试时将同时测试剎车功能
- After the main switch was switched off, an EMERGENCY STOP test is
always run.
- The test must be repeated after 168 hours; it starts automatically.
Prerequisites:
- Doors are closed
- No running NC program
- Axes and spindle are stopped
- 关电重开后将进行紧急停止测试.
- 每 168 个小时将自动要求进行测试.
测试前须求:
- 安全门关闭
- 未执行程序
- 轴向及主轴停止
123 Key non-functional
123 按键功能无效
In this context the key has no function.
e.g.
123
- handwheel mode for HR420/HR5xx not on TE keyboard selectable
(use handwheel key)
- 在此状态下,此按键没有功能
比如：
- HR420/HR5xx 的手轮模式按钮不在 TE 键盘上而是在手轮上。
124 EnergyOpt
-> Machine switched off
124 能量优化
->机械关机
- Machine inactive
- Axis and Spindle in position
124
- NC Program inactive
- 机械未启动
- 轴向及主轴未移动
- NC 程序未启动
- Delite the error with the CE
- Switch on the Machine orSwitch off EnergyOpt
- 使用 CE 键清除错误
- 启动机械或关闭能源优化功能
125 EnergyOpt
-> AUTOSTART / warmup program active
125 能量优化
->自动启动
- The machine will be switch on at the specified time automatically
by EnergyOpt.
125
- Dependent to the configuration the drives or rather the warmup
program will started
- Energyopt 会将机器在设定的时间到达时自动启动。
-依照设定，驱动装置或暖机程序也会启动。
- Press the emergancy stop button
Or switch off EnergyOpt
- 按紧急停止按钮
或关闭 EnergyOpt
126 TNC/IP Client 1
-> Connection Error 126 TCP/IP 从属端 1
126 ->联机错误
- Error while sending data from PLC via TCP/IP sockets.
- Timeout.
- Connection Error PLC -> Python.
- Server not reachable.
- Python process crashed.
- PLC 透过 TCP/IP socket 传送数据时发生错误
- 时间过长
- PLC --> Python 联机错误
- Python 程序错误
- Please contact the OEM
- 请联络机械制造商
127 TNC/IP Server
-> Connection Error
127 TCP/IP 伺服端
->联机错误
- Error while sending data from PLC via TCP/IP sockets.
- Connection Error PLC -> Python.
127 - Client not reachable.
- Python process crashed.
- PLC 透过 TCP/IP socket 传送数据时发生错误
- PLC --> Python 联机错误
- 无法联机至 Client 端
- Python 程序错误
- Please contact the OEM
- 请联络机械制造商
128 Error in python mask
128 Python mask 错误
- A python mask raised an error.
- Python process terminated.
- Memory allocation error.
- Pytnon Mask 档产生错误
128 - Python 程序中断
- Please contact the OEM
- 内存分配错误
- 请联络机械制造商
129 129 Error left softkey menu
129 左功能键选单错误
- The left softkey menu raised an error.
- Python process terminated.
- Memory allocation error.
- 左功能键选单引发了一个错误
- Python 进程终止
- 内存分配错误。
- Please contact the OEM
- 请联络机械制造商
130 TT449 battery low
130 TT449 电池电量过低
130 - TT449 battery voltage too low
- TT449 电池电量过低
- change battery
- 换新的电池
131 Spindle lubrication air oil alarm
131 主轴油气警报器
-Source air pressure too low
131 -Tube broke
- 源头气压过低
- 管破裂
-Check source air pressure
-Check tube
- 检查源头空气压力
- 检查管路
132 Spindle lubriaction low level
132 主轴润滑油低油位
132 - Spindle lubrication oil not enough
- 主润轴润滑油不足
- Fill oil to tank.
- 油箱请补油
133 Chip conveyer motor overload
133 排削机马达超载
133 - Chip conveyor motor overload
- 排削机马达超载
- Check conveyor motor system and circuit loop
- 检查马达系统和电路回路
134 Screw motor overload
134 螺旋卷削马达超载
- Screw motor overload
134 - 螺旋卷削马达超载
- Check screw motor protect switch
- 检查螺旋卷削马达保护开关
135 135 Mist oil level low
135 油雾溢面过低
- Mist oil level low
- 油雾溢面过低
- Check oil mist tank.
- 检查油雾箱
136 Hydraulic pump overload
136 油压泵超载
136 - Hydraulic pump overload
- 油压泵超载
- Check Hydraulic pump system and circuit loop
- 检查的液压泵系统和电路循环
137 C.T.S. filter pressure too hight
137 CTS 过滤器压力过高
137 - CTS filter pressure too high
- CTS 过滤器压力过高
- Clean the CTS filter
- 检查 CTS 滤清器
138 A.T.S. oil tank level low
138 ATS 油箱油位低
138 - Air through spindle oil tank level low
- ATS 油箱油位低
- Check air through spindle oil tank level low
- 检查 ATS 油箱油位
139 C.T.S. tank low level
139
139 CTS 水箱低水位
- Cooler through spindle tank low level
- CTS 水箱低水位
- Check cooler through spindle tank system and circuit system
- 检查 CTS 系统和电路系统
140 Balance pump overload
140 平衡泵超载
140 - Balance pump overload
- 平衡泵超载
- Check balance pump system and circuit loop
- 检查平衡泵系统和电路系统
141 C.T.S. coolant missing
141 CTS 无切削液
141 - Cooler through spindle coolant missing
- CTS 无切削液
- Refill coolant to tank
- 请补充切削液
142 Coolant tank high level alarm
142
142 水箱高水位警报
- Coolant tank high level
- 水箱高水位警报
- Check coolant tank system and circuit loop
- 检查切削液系统和电路系统
143 Coolant low level alarm
143 水箱低水位警报
143 - Coolant low level alarm
- 水箱低水位警报
- Check coolant system and circuit loop
- 检查切削液系统和电路系统
144 Level sensor not ok
144 液位传感器不能确定
144 - Level sensor not ok
- 液位传感器不能确定
- Check level sensor
- 检查液位传感器
145 Coolant through spindle motor overload
145
145 主轴中心出水马达超载
- Coolant through spindle motor overload
- 主轴中心出水马达超载
- Check coolant through spindle motor system and circuit loop
- 检查主轴中心出水电机系统和电路回路
146 X1 Axis motor overtemperature
146 146 X1 轴马达温度过高
- Coolant tube was broke or coolant system is not normal
-Parameter is wrong
- 冷却液管或冷却系统不正常
- 参数不正确
- Check coolant tube loop and coolant system
-Check axis parameters is ok
- 检查冷却液管循环冷却系统
- 检查轴参数的确定
147 U1 Axis motor overtemperature
147 U1 轴马达温度过高
- Coolant tube was broke or coolant system is not normal
-Parameter is wrong
147 - 冷却液管或冷却系统不正常
- 参数不正确
- Check coolant tube loop and coolant system
-Check axis parameters is ok
- 检查冷却液管循环冷却系统
- 检查轴参数的确定
148 Y1 Axis motor overtemperature
148 Y1 轴马达温度过高
148 - Coolant tube was broke or coolant system is not normal
-Parameter is wrong
- 冷却液管或冷却系统不正常
- 参数不正确
- Check coolant tube loop and coolant system
-Check axis parameters is ok
- 检查冷却液管循环冷却系统
- 检查轴参数的确定
149 Z1 Axis motor overtemperature
149 Z1 轴马达温度过高
- Coolant tube was broke or coolant system is not normal
-Parameter is wrong
149 - 冷却液管或冷却系统不正常
- 参数不正确
- Check coolant tube loop and coolant system
-Check axis parameters is ok
- 检查冷却液管循环冷却系统
- 检查轴参数的确定
150 B1 Axis motor overtemperature
150 B1 轴马达温度过高
- Coolant tube was broke or coolant system is not normal
150 -Parameter is wrong
- 冷却液管或冷却系统不正常
- 参数不正确
- Check coolant tube loop and coolant system
-Check axis parameters is ok
- 检查冷却液管循环冷却系统
- 检查轴参数的确定
151 C1 Axis motor overtemperature
151 C1 轴马达温度过高
- Coolant tube was broke or coolant system is not normal
-Parameter is wrong
151 - 冷却液管或冷却系统不正常
- 参数不正确
- Check coolant tube loop and coolant system
-Check axis parameters is ok
- 检查冷却液管循环冷却系统
- 检查轴参数的确定
152 Emergency stop
152 紧急停止
- Emergency stop is additional action
152 - 紧急停止已动作
- Emergency stop is an additional action.Please Check the major
alarm message for fix.
- 紧急停止是一个额外的行动。请检查修复的主要报警消息。
153 AMP cooler alarm
153 153 AMP 冷却器报警
- Power supply overheat or AMP cool alarm
- 电源供应器过热或是 AMP 冷警报
- Please check power supply working correct and check AMP cooler
device ok.
- 请检查电源工作正确,并检查 AMP 冷却设备确定。
154 Axis cooler alarm
154 轴冷却警报
154 - Axis cooler system alarm
-轴冷却系统警报
- Check axis cooler system and circuit loop
- 请检查轴冷却系统和电源系统
155 Spindle cooler system alarm
155 主轴冷却系统报警
155 - Spindle cooler system alarm
-主轴冷却系统报警
- Check spindle cooler system and circuit loop
- 检查主轴冷却系统和电路回路
156 Axis motor cooler system overload
156 轴马达冷却器超载
156 - Axis motor cooler system overload
- 轴马达冷却系统超载
- Check axis motor cooler system and circuit loop
- 检查轴马达的冷却系统和电路回路
157 AMP cooler overload
157 AMP 冷却器超载
157 - AMP cooler overload
- AMP 冷却器超载
- Check AMP cooler and AMP protect device
- 检查 AMP 冷却器和 AMP 保护装置
158 Air Dryer overload
158 空气干燥机超载
158 - Air Drier overload
- 空气干燥机超载
- Check Air Drier and protect device
- 检查空气干燥器和保护装置
159 Spindle sub tank overload
159 主轴副箱超载
159 - Spindle sub tank overload
- 主轴副箱超载
- Check spindle sub tank and protect device
- 检查主轴副箱和保护装置
160 160 X Axis right brake air low
160 X 轴右制动气压低
- Source air pressure too low
-Missing air in the loop
- 源头气压过低
- 缺少空气循环
- Check source air wheather is enough
-Check air loop is ok
- 检查源头空气是否充足
- 检查空气循环“
161 X Axis left brake air low
161 X 轴左制动气压低
- Source air pressure too low
-Missing air in the loop
161 - 源头气压过低
- 缺少空气循环
- Check source air wheather is enough
-Check air loop is ok
- 检查源头空气是否充足
- 检查空气循环
162 Y Axis brake air low
162 Y 轴右制动气压低
- Source air pressure too low
162 -Missing air in the loop
- 源头气压过低
- 缺少空气循环
- Check source air wheather is enough
-Check air loop is ok
- 检查源头空气是否充足
- 检查空气循环
163 Z Axis brake air low
163 Z 轴制动气压低
- Source air pressure too low
-Missing air in the loop
163 - 源头气压过低
- 缺少空气循环
- Check source air wheather is enough
-Check air loop is ok
- 检查源头空气是否充足
- 检查空气循环
164 B axis unclamp alarm
164 B 轴松开报警
164 - B axis unclamp alarm
- B 轴松开报警
- Check a axis unclamp signal.
- 检查一个轴松开信号
165 C axis radial unclamp alarm
165 165 C 轴的径向松开报警
- C axis radial unclamp alarm
- C 轴的径向松开报警
- Check c axis radial unclamp signal.
- C 轴的径向松开信号
166 C axis axial unclamp alarm
166 C 轴的轴向松开报警
166 - C axis axial unclamp alarm
- C 轴的轴向松开报警
- Check c axis axial unclamp signal
-C 轴轴向松开信号
167 Tool magazine switch in manual mode
167 在手动模式下的刀库开关
167 - Tool magazine switch in manual mode
- 在手动模式下的刀库开关
- Information only
- 仅是信息
168 Magazine motor overload
168 刀库马达超载
168 - Magazine motor overload
- 刀库马达超载
- Check circuit loop and magazine rotation
- 检查回路和刀库旋转
169 Mist oil overload
169 喷雾油超载
169 - Mist oil overload
- 喷雾油超载
- Check mist oil tank and protect device
- 检查油雾的油箱和保护设备
- Check mist oil tank and protect device
170 - 检查油雾的油箱和保护设备
- Spindle cooler system overload
- 主轴冷却系统超载
- Check spindle cooler system and circuit loop
- 检查主轴冷却系统和电路回路
171 C.T.S. PAPER FILTER PUMP overload
171 CTS 纸袋过滤机泵浦超载
171 - Cooler through spindle paper filter pump overload
- CTS 纸袋过滤机泵浦超载
- Check Cooler through spindle paper filter pump and protect device
- 检查纸袋过滤机泵浦和保护装置
172 Air conditioner alarm
172 空调报警
172 - Air condition alarm
- 空调报警
- Check air condition system
- 检查空调系统
173 Spindle sub tank level low
173 主轴副箱水位低
- Spindle sub tank level low
173 - 主轴副箱水位低
- Fill oil to tank
- 油箱补油
174 Chip conveyor EMG
174 排屑机紧急停止
174 - Chip conveyor EMG.
- 排屑机紧急停止
- Release chip conveyor EMG.
- 松开排屑机紧急停止
175 Coolant motor overload
175 冷却液马达超载
175 - Coolant motor overload
- 冷却液马达超载
- Check coolant motor and circuit loop
- 检查冷却液马达及电路回路
176 Air conditioner alarm
176 空调异常
176 - Air conditioner alarm
- 空调异常
- Check air conditioning and protect device
- 检查空调和保护装置
177 Axis lubricant overload
177 177 轴润滑超载
- AXIS lubricant overload
- 轴润滑超载
- Check AXIS lubricant and protect device
- 检查轴的润滑剂和保护装置
178 Service mode
178 服务模式
178 - Service mode
- 服务模式
- Service mode
- 服务模式
179 Lubricant X1 pressure low
179 X1 润滑油压力过低
- Lubricttion X1 press low
179 - X1 润滑油压力过低
- Visual inspection for oil loss
-Electrical connection of pressure switch
- 目视检查油的损耗
- 电气连接的压力开关
180 Lubricttion X2 press low
180 180 X2 润滑油压力过低
- Lubricttion X2 press low
- X2 润滑油压力过低
- Visual inspection for oil loss
-Electrical connection of pressure switch
- 目视检查油的损耗
- 电气连接的压力开关
181 Lubricttion YZ press low
181 YZ 润滑油压力过低
- Lubricttion YZ press low
181 - YZ 润滑油压力过低
- Visual inspection for oil loss
-Electrical connection of pressure switch
- 目视检查油的损耗
- 电气连接压力的开关
182 Heater exchange overload
182 热交换器超载
- Heater exchange overload
182 - 热交换器超载
- Check Heater exchange and protect device
- 检查热交换器和保护装置
183 Vacuum motor overload
183 183 真空马达超载
- Vacuum motor overload
- 真空马达超载
- Check Vacuum motor and protect device
- 检查真空马达保护装置
184 Spindle Lubrication overload
184 主轴润滑机超载
184 - Spindle lubricant overload
- 主轴润滑机超载
- Check Spindle lubricant and protect device
- 检查主轴润滑机和保护装置
185 Spindle lubrication low pressure
185 主轴润滑机压力过低
185 - Spindle lubricant low pressure
- 主轴润滑机压力过低
- Check Spindle lubricant and pressure device
- 检查主轴润滑机和压力装置
186 Spindle lubrication error
186 主轴润滑机错误
186 - Spindle sub lubrcation fill not ready
- 主轴副油箱未准备好
- Check lubrcation pipe
-Check lubrication level sensor
- 检查润滑管
- 检查润滑油液位检知器
187 C Axis Position is Warning
187 C 轴的位置是错误的
- C Axis Position is Warning
- C 轴的位置是错误的
187 - Check C Axis position.
-Axis on end position C+(>240).
-Axis on end position C-(<240).
-Please Recovery C axis position.
- 检查 C 轴的位置。
- 轴结束位置 C +（> 240）。 - 轴结束位置 C -（<240）。
- 请恢复 C 轴的位置。
188 Machine feed hold
188 188 机床进给暂停
- Machine feed hold
- 机床进给暂停
189 Spindle back sensor not in position
189 主轴夹刀确认位置错误
189 - Spindle back sensor not in position
- 主轴夹刀确认位置错误
- Check spindle clamp piston back seneor
- 检查电气回路是否短路或断路
- 检查检知是否异常
190 Source voltage overload185
190 电压保护器过载
190 - Source voltage overload
- 电压保护器过载
- Please check Source voltage
- 检查入电电压是否异常
191 Hydraulic MAG Low pressure
191 刀库油压压力过低
- No pressure build-up in hydraulic system
- Pressure loss - leaky pipe work
- Pressure switch defective
-刀库油压压力过低
- Visual inspection for oil loss
191 - Electrical connection of pressure switch
- 检查润滑管
- 检查润滑油液位检知器
192 Spindle bearing overheat
192 192 主轴培林温度过高
- Coolant tube was broke or coolant system is not normal
- Parameter is wrong
-主轴培林温度过高
- Check coolant tube loop and coolant system
- Check axis parameters is ok
-检查温度检知是否异常
-检查主轴温度是否超过原厂出场值
193 C Axis limit +
193 C 轴过极限 +
193 - C Axis limit
- C 轴过极限 +
- Move out c axis limit
-请脱离极限位置
194 C Axis limit -
194 C 轴过极限 -
194 - C Axis limit
- C 轴过极限 -
- Move out c axis limit
- 请脱离极限位置
195 Chip clean motor overload
195 195 侧喷马达过载
- Chip clean motor overload
- 侧喷马达过载
- Check machine Oil skimmer motor
- 检查是否有短路或断路
- 检查线圈阻抗是否过高
200 ASDA magazine alarm
200 台达刀库马达报警
200 - Magazine inverter alarm
- 台达刀库马达报警
- Check magazine inverter alarm from LED
- 检查台达驱动器面板上 LED 提示报警进行排除
201 Oil skimmer overload
201 油水分离机过载
- Oil skimmer overload
201 - 油水分离机过载
- Check machine Oil skimmer motor
- 检查是否有短路或断路
- 检查线圈阻抗是否过高
202 ZF flow rate not enough
202 202 齿轮箱流量过低
- ZF flow rate not enough
- ZF 齿轮箱流量过低
- Check ZF flow rate
- 检查流量检知是否异常
- 检查流量阀门设定是否异常
- 检查油冷机是否异常
203 Head flow rate not enough
203 头部齿轮箱流量过低
- Head flow rate not enough
203 - 头部齿轮箱流量过低
- Check Head flow rate
- 检查流量检知是否异常
- 检查流量阀门设定是否异常
- 检查油冷机是否异常
204 ZF suction oil motor overload
204 ZF 抽油马达过载
- ZF suction oil motor overload
204 - ZF 抽油马达过载
- Check ZF suction oil motor breaker
- 检查是否有短路或断路
- 检查线圈阻抗是否过高
- 检查油管是否破裂
205 BC lubrication motor overload
205 BC 轴 抽油马达过载
- BC lubrication motor overload
205 - BC 轴抽油马达过载
- Check BC lubrication motor breaker
- 检查是否有短路或断路
- 检查线圈阻抗是否过高
- 检查油管是否破裂
206 SP lubrication motor overload
206 主轴抽油马达过载
- SP lubrication motor overload
206 - 主轴抽油马达过载
- Check SP lubrication motor breaker
- 检查是否有短路或断路
- 检查线圈阻抗是否过高
- 检查油管是否破裂
207 BC axis Tension pressure alarm
207 207 BC 轴 油压预压报警
- BC axis Tension pressure alarm
- BC 轴 油压预压报警
208 B axis limit +/-
208 B 轴过极限 +/-
- B axis limit +/-
208 - B 轴过极限 +/-
-依照下方提示是否为正或负方向
-使用极限解除,进行排除
209 arm motor overload
209
209 刀臂马达过载
- arm motor overload
- 刀臂马达过载
- Check conveyer motor system and circuit loop
- 检查刀臂马达回路是否短路
Reference in New Issue View Git Blame Copy Permalink