69 KiB
PLC 警报表
000 Circuit breaker
000 电路断路
- Overload of protective motor switch
- Motor defective
0 - 马达保护开关超载 - 马达损坏 - Check electrical cabinet - Electrical motor check - 检查电器箱 - 检查马达 001 Temperature drive / inverter 001 驱动器/换流器温度异常 - Overload of drives - Filter of fan contaminated - Fan in switch cabinet defective - 驱动器超载
1 - 风扇滤网污染 - 电器箱风扇开关损坏 -Check motor temperature - Change filter - Check if the fan functions - 检查马达温度 - 更换滤波器 - 检查风扇功能 002 Hydraulic pressure 002 油压异常 - No pressure build-up in hydraulic system
2 - Pressure loss - leaky pipe work - Pressure switch defective - 油压无压力 - 压力管线泄漏 - 压力开关损坏 - Visual inspection for oil loss - Electrical connection of pressure switch - 检查油料耗损 - 检查压力开关接线 003 Pneumatic pressure 气压系统故障 - Pressure loss - leaky pipe work - Pressure switch defective
3 - 压力管件泄漏 - 压力开关损坏 - Visual inspection of pipe work - Check the pressure switch - 检查压力管 - 检查压力开关 004 PW 210 temperature max 004 PW210 温度到达极限 - Brake overload drives
4 - 驱动器煞车超载 - Optimize machine parameters - Reduce feed rate - 调整参数 - 降低进给 005 DA300 pressure 005 DA300 压力异常 - Pressure loss leaky pipe work - Pressure switch defective
5 - 压力管件泄漏 - 压力开关损坏 - Change filter - Visual inspection of pipe work - Check the pressureswitch - 更换滤材 - 检查压力管 - 检查压力开关 006 Power supply drives 006 电源供应器异常 - Supply and recovery unit not operational - 供应及回升单元无动作 - Check supply and recovery unit
6 - Check connection PLC input - Siemens SIMODRIVE 611 ER module (X111 72-73.1) - Indramat Power Drive supply unit HVE (X7 3-4) - 检查供应及回复单元 - 检查 PLC 输入点接线 - 西门子 SIMODRIVE 611 ER module (X111 72-73.1) - Indramat 电源供应器 HVE (X7 3-4) 007 Release M07 for Txxx inactive 007 TXXX 不允许使用 M07 - Tool-specific release for M07 "Coolant, inside" in TOOL.T is inactive. - 刀具表中特定刀具 M07"中心出水"功能未启动。 - If the tool provides M07 "Coolant inside" the functioncan be enabled via TOOL.T
7 PLC Status #Bit2. PLC status for M07: - %xxxxx0xx = M07 disabled - %xxxxx1xx = M07 enabled - 如果此刀具可使用 M07 中心出水功能，则在 TOOL.T 刀具表中 PLC Status #Bit2 中设定。 PLC Status 中 M07 设定: - %XXXXX0XX = M07 取消 - %XXXXX1XX = M07 启动 008 Clamping mode not permitted(Tapping Cycle)
8 008 不可启动夹持模式(攻牙循环) - A tapping cycle has been called while the tool axisis in clamping mode. - 在刀具轴夹持模式下呼叫攻牙循环 - Program M- or FN19 function to disable the clamping mode of the tool axis before the cycle call. e.g. Z-axis FN 19: PLC =+99991 / +4 - 呼叫攻牙循环前使用 M 功能或 FN19 取消刀具轴夹持. 例如 Z 轴 FN 19: PLC =+99991 / +4 009 Machine guard is closed ! 009 安全门关闭! - Guards not opened - Sensors defective
9 - 门锁未开 - 传感器损坏 - Open guards - Check sensors - 开门 - 检查传感器 010 Machine guard is open ! 010 安全门开启! - Guards not closed - Sensors defective
10 - 门锁未关 - 传感器损坏 - Close guards - Check sensors - 关门 - 检查传感器 011 Coolant level low
11 011 冷却液水位过低 - Coolant level too low - Level switch defective - 冷却液液面过低 - 液位传感器故障 - Refill coolant - Check the level switch - 重新装填冷却液 - 检查液位传感器 012 Lubricating axes 轴润滑故障 - Lubrication cycle of axes not carried out correctly - Pressure loss - leaky pipe work - Pressure switch defective
12 - 轴向润滑循环未正确启动 - 压力管件泄漏 - 压力开关损坏 - Visual inspection for oil loss - Electrical connection of pressure switch - 检查油料损失 - 检查压力开关接线 013 Lubrication oil level low 013 润滑油油位过低 - Oil level of central lubrication system too low - Level switch defective
13 - 中心润滑系统液面过低 - 液面开关损坏 - Refill oil - Check the level switch - 从新装填油料 - 检查液面开关 014 Servo drive release I32 014 伺服驱动器释放 I32 - Axes are ready to power on - Servo drive release I32 is missing - 轴向准备通电 - 伺服驱动器 I32 未正常作动
14 - Check wiring Interface NE2 MC42xx - X42/33 - 检查接线接口 NE2 MC42xx - X42/33
015 Servo drive release X150/X151 -> Axes group: %d
015 伺服驱动器释放 X150/X151 ->轴群组: %d
- Axes are ready to power on
- Servo drive release X151/X151 is missing
- 轴向准备通电
- 伺服驱动器 X150/X151 未正常作动
15 - Check wiring Interface XX42x - X150/X151 - Check safety contactor combination, both channels should beactive. - 检查接线 界面 XX42x - X150/X151 - 检查是否安全接触，2 条电线通道应该要有作用 016 Servo drive release inverter UM 016 伺服驱动器模块 UM 未释放 - The axis inverter module (UM) is not READY, no messageto CC4xx
16 - 轴向模块(UM)未准备完成,没有讯号到 CC4xx - Check PWM cable - Pulse release (spindle or axis) not active - X71/X72 - 检查 PWM 电缆线 - 主轴没有动作-X71/X72 017 Central drive 017 中央驱动模式错误 - Several axes with central drive were started at the same time - 多个轴向中心驱动同时启动
17 - Change NC program - Each NC block must include only one axis with central drive. - 检查 NC 程序 - 每一 NC 单节必须只能包含一个中心驱动轴 - 中心驱动轴轴向键不可同时按压 018 Positioning error TC magazine 018 刀库定位错误 - Tool magazine blocked or jammed - Tool magazine loaded unevenly - Axes optimization faulty
18 - 刀库卡住 - 刀具无法上刀 - 轴向未伺服调整 - Check tool distribution - Optimize axes - 检查刀具 - 轴向伺服调整 019 Axis motion from end position 019 轴向脱离极限位置 - One or more of the axes has triggered an over travel -limit switch resulting in an Emergency stop - 轴向已经将硬件极限开关紧急停止解除 - 由急停引起的限位报警 - (1) Select Manual operating mode
19 - (2) Close guard - (3) Press "Retract" button - (4) Switch control on - (5) Clear error message Emergency stop (CE key) - (1) 选择手动操作模式 - (2) 按压" 回复" 或 "Retract" 按钮 - (3) 启动 - (4) 清除紧急停止错误讯息(CE)键 - (5) 使用箭头键回归 020 Clamping/unclamping axes -> axis %s (%d)
20 020 轴向夹持/松开 ->轴 %s (%d) - Sensors for clamping/releasing defective - Pressure drop of pneumatic/hydraulic system - [->] Additional note in PLC window: Identifies the axis - 夹松讯号传感器损坏 - 油/空压压力不足 - [->] PLC 窗口附加讯息: 错误轴向 - Check sensors and re-adjust them if required - Check compressed-air and hydraulic pressure - 检查传感器或重新调整压力 - 检查空压或油压 021 Axis not in hirth position -> axis %s (%d) 021 轴向不在固定分度位置 ->轴 %s (%d) - Axis not in Hirth position - Axis movement was interrupted
21 - 轴向不是在分度位置 - 轴向移动中止 - Encoder/coupling loose - Compensate reference mismatch via MP960 - Position the axis in manual operating mode on Hirth grid - 编码器松脱 - MP960 原点位置补偿错误 - 重新以手动定位到正确位置 022 Nominal position not in hirth -> axis %s (%d) 022 指令位置不在正确分度位置->轴 %s (%d)
22 - Programmed target position not in Hirth grid - 程序编辑位置不是分度位置 - Correct the NC program - 补偿或修改 NC 程序 023 Drives not operational
23 -> axis %s (%d) 023 驱动器未启动 ->轴 %s (%d) - Axis drive not ready - [->] Additional note in PLC window: Identifies the axis - 轴向驱动未待命状态 - [ -> ] PLC 窗口附加讯息: 轴向错误 - Check hardware of axis drive; check diagnosis LED - Switch unit on/off - 利用灯号检查轴向驱动硬设备 - 硬件重新开关机
024 Power stage temperature max
-> axis %s (%d)
024 电源供应器温度过高
->轴 %s (%d)
- Overload of servo drive controller
24 - Filter contaminated - 轴向伺服控制超载 - 过滤棉污染阻塞 - Reduce feed rate - Check / change filter - 降低进给 - 检查/ 更换过滤棉 025 Drives temperature max -> axis %s (%d) 025 驱动器温度过高 ->轴 %s (%d) - Overload of servo drives
25 - 伺服驱动超载 - Check temperature of motors - Reduce feed rate - Switch unit on/off - 检查马达温度 - 降低进给率 - 硬件重新开关机 026 Axes i2t pre-warning -> axis %s (%d) 026 轴向 i2t 电流-温度预警 ->轴 %s (%d)
26 - Overload of servo drives - 伺服驱动超载 - Reduce feed rate - Select smaller tools - 降低进给率 - 选择较小刀具 027 Axes i2t limitation -> axis %s (%d) 027 轴向 i2t 电流-温度预警极限 ->轴 %s (%d)
27 - Overload of servo drives - 伺服驱动超载 - Reduce feed rate - Select smaller tools - 降低进给率 - 选择较小刀具 028 Spindle not perational 028 主轴未运作 - Overload of spindle - Spindle drive defective - Spindle motor defective - 主轴超载
28 - 主轴周边控制损坏 - 主轴马达损坏 - Reduce feed rate - Check / change filter - Check spindle motor - Check cable / screwed onnection - 降低进给率 - 检查周边控制 - 检查主轴马达 - 检查接线 029 Spindle nominal rpm 029 主轴转速差过大 - Nominal speed not reached or too low - 无法到达指令速度或速度太低 - Reduce feed rate
29 - Select smaller tools - Check speed with oscilloscope - Optimize machine parameters - 降低进给率 - 选择较小刀具 - 利用示波器检查速度 - 调整机械参数 030 Spindle stand still monitor 030 主轴定位异常 - Offset too high, spindle drifts - Encoder or cable defective - 主轴马达超载 - 主轴风扇污染
30 - Compensate offset (analog) - Check encoder (oscilloscope) - Check cable - Optimize machine parameters - 检查平移(模拟控制) - 检查编码器(示波器) - 检查接线 - 调整机械参数 031 Spindle I max
31 031 主轴电流过大 - Overload of spindle motor - Spindle motor fan defective/not running - 主轴马达超载 - 主轴风扇污染 - Reduce cutting values - Check the fan - 降低切削数值 - 清洁主轴马达风扇 032 Spindle T max (sensor Pt100) 032 主轴温度过高 (Pt100 温度传感器) - Excessive temperature in spindle bearing - Pt 100 temperature sensor defective - Spindle motor fan defective - 主轴培林温度过高
32 - Pt100 温度传感器损坏 - 主轴马达风扇损坏 - Reduce spindle speed - Check Pt 100 temperature sensor - Check spindle fan - 降低主轴转数 - 检查 Pt100 温度传感器 - 检查主轴风扇 033 Spindle max torque 033 主轴到达最大扭力 - Maximum permissible torque exceeded - 超过最大容许扭力 - Reduce feed rate
33 - Increase spindle speed - Select smaller tools - Optimize machine parameters - 降低进给率 - 增加主轴转速 - 选择较小刀具 - 调整机械参数 034 Touch probe in spindle !
34 034 主轴有量测探针 - M03, M04, M05, M13, M14 only permissible if there is no touch probe in the spindle. (no Probe in the PLC window) - M03, M04, M05, M13, M14 只容许主轴没有量测探针才可执行。 (PLC 窗口中没有探针讯息) - Change the tool (with PLC status %00000000) PLC status for code of tool type - 更换刀具 (PLC status %00000000) PLC status 对应刀具编码 - %00000000 = normal tool - %00000001 = touch probe - %00000000 = 正常刀具 - %00000001 = 量测探针 035 Touch probe not in spindle ! 035 主轴无量测探针 - Probe function selected but no touch probe in the spindle ("Probing" should flash in the PLC window) - 已选择量测功能但主轴没有量测探针
35 (PLC 窗口中需有探针讯息) - Change the touch probe PLC status for code of tool type - %00000000 = normal tool - %00000001 = touch probe - 更换刀具 PLC status 对应刀具编码 - %00000000 = 正常刀具 - %00000001 = 量测探针 036 Spindle 1/2 activation 036 第 1/2 主轴启动异常 - The switching between spindle S1 and S2 was defective
36 - 在 S1 与 S2 主轴之间切换有问题 - Check MP settings (MP4020 bit 5) - Check setting of MP3010/MP13010 - 检查 MP 的设定(MP4020 bit 5) - MP3010/MP13010 是无法提供给 2 个主轴模式 037 Gear change
37 037 主轴换档异常 - The selected gear range cannot be coupled - 选择的档位无法结合 - Check sensors for the gear ranges - Clear error message (CE key) and retry - 检查档位传感器 - 清除错误讯息后重新测试 038 Tool not clamped ! 038 刀具未夹持! - Tool change interrupted - Tool unclamped - Sensors or cables defective
38 - 换刀中断 - 刀具松刀 - 传感器或接线损坏 - Press the key "Clamp tool" - Check the sensors - 按压"夹刀"键 - 检查传感器 039 Tool unclamping, please ! 039 请松刀! - Call for Manual tool change - Tool clamped - 手动换刀的调用 - 刀具夹紧了
39 - Press the key "Unclamp tool" - Remove the tool - 按压键 "松刀" - 取出刀具 040 Tool clamping, please ! 040 请夹刀!
40 - Call for Manual tool change - Tool unclamped - 呼叫手动换刀 - 刀具松刀 - Press the key "Clamp tool" - Insert the tool - 按压"夹刀"键 - 插入刀具 041 TC quit, please ! 041 请结束换刀! - Call for Manual tool change
41 - Tool change carried out - 呼叫手动换刀 - 换刀完成 - Press the key "Confirm tool change" - 按压" 确认换刀"键 042 Close guard -> TC quit ! 042 门关 -->换刀结束 - Call for Manual tool change - Tool change carried out
42 - 呼叫手动换刀 - 换刀完成 - Close the guard - Press the key "Confirm tool change" - 关门 - 按压" 确认换刀"键 043 TC end -> NC start 043 换刀结束 -->按程序启动 - Call for a Manual tool in Auto mode
43 - Tool change carried out - 呼叫手动换刀 - 换刀完成 - Press the NC start key to resume program run. - 按压程序启动键 044 Check pocket table !
44 044 检查刀套表! - Interruption during tool change - It is possible that the pocket table does not correspond to the loading of the magazine - 换刀中断 - 刀套表与刀库对应可能错误 - Check/correct the pocket table - 检查/更正刀套表 045 Correct tool in spindle ? 045 主轴刀号正确? - The tool was unclamped without TOOL CALL - 刀具在没有呼叫刀具松刀 - Check if the tool shown in the status is in the spindle and whether it
45 can be placed in the magazine - NC start to carry out the tool change - NC stop to interrupt the tool change - 检查刀具状态是在主轴或刀库 - 按压程序启动键执行换刀 - 按压程序停止键结束换刀 046 Spindle is empty ! 046 主轴空刀! - There is no tool in the spindle - Sensor defective
46 - 主轴无刀 - 传感器损坏 - Insert the tool - Check the sensor - 插入刀具 - 检查传感器 047 Spindle is not empty ! 047 主轴有刀!
47 - There is a tool in the spindle although P0 in the pocket table is empty - Sensor defective - 主轴有刀,但刀套表中 P0 无刀具 - 传感器损坏 - Remove the tool from the spindle - Check the sensor - 将刀具从主轴移除 - 检查传感器 048 Tool call T0 necessary ! 048 需先呼叫 T0 刀 - Special function in case of tool change of tools withand without magazine pocket
48 - Can be activated via MP - 特殊换刀功能，换刀执行更换非刀套刀 - 可使用参数启动 - Change the NC program. First the tool must be removed from the spindle (TOOL CALL 0) before a new tool is inserted. - 更改 NC 程序，换刀前首先需移除主轴刀具 049 Tool not in tolerance 049 刀具尺寸超过误差
49 - Tolerance in tool table exceeded! - 超过刀具表中设定之误差 - Check the tool - 检查刀具 050 Tool life maximum 050 刀具最大寿命到达 - Tool life in tool table exceeded! - 刀具使用时间超过刀具表设定寿命 ! - Check the tool
50 - Set the current tool life to 0 - 检查刀具 - 将目前刀具使用寿命设为 0 051 Tool change basic position
51 051 换刀基本位置异常 - Tool change interrupted - Error during tool change - 换刀中断 - 换刀中错误产生 - Move the tool change arm/magazine to their 'home' positions by means of the service function (Help)inManual mode - Test the inputs - 进入手动模式利用除错模式(HELP)，移动至正确位置 - 测试 PLC I/O 输入点 052 Tool change timeout 052 换刀时间过长 - Timeout during tool change - Interruption of tool change
52 - 换刀时间过长 - 中断换刀 - Press NC start key to continue the tool change - Press internal stop soft key to stop the tool change - 按压程序启动继续进行换刀 - 按压中断程序软键停止换刀 053 TC magazine guard open ! 053 刀库门打开!
53 - Magazine guard open - 刀库门开 - Close the tool magazine guard - 关闭刀库门 054 TC magazine reference 054 刀库原点未复归
54 - Tool magazine has not been referenced - 刀库未原点复归 - NC start to reference the tool magazine - 按压程序启动执行原点复归 055 TC magazine timeout
55 055 刀库动作时间过长 - Timeout when positioning the toolmagazine - Tool change interrupted - 刀库定位时间过长 - 换刀中断 - Press NC start key to continue tool change - Press internal stop soft key to interrupt tool change - 按压程序启动继续执行换刀 - 按压程序中断终止换刀 056 TC magazine loading active ! 056 刀库上下刀动作中! - Loading of the tool magazine selected via soft key
56 - Tool magazine can be traversed and loaded - 使用软键启动刀库上下刀功能 - 刀库可以移动及上下刀具 - Information only - 仅供提示 057 TC magazine pocket not empty 057 刀套有刀 - Tool magazine not loaded correctly - Erroneous entries in the pocket table - Sensor defective - 刀库上刀错误
57 - 刀套表输入错误 - 传感器损坏 - Load the tool magazine correctly - Check the pocket table - Check the sensor - 刀具重新上刀 - 检查刀套表 - 检查传感器 058 TC magazine pocket is empty 058 刀套无刀
58 - Tool magazine loaded incorrectly - Erroneous entries in the pocket table - Sensor defective - 刀库上刀错误 - 刀套表输入错误 - 传感器损坏 - Load the tool magazine correctly - Check the pocket table - Check the sensor - 刀具重新上刀 - 检查刀套表 - 检查传感器 059 Wrong tool in spindle 059 主轴刀具错误 - Block scan was stopped - Different tools in status line and spindle
59 - 单节扫描停止 - 主轴刀状态或刀号错误 - In the MDI operating mode, insert the tool displayed in the status line - 在手动输入模式, 在状态中输入刀具显示 060 Alternating table timeout 060 交替工作台动作时间过长 - The alternating table cycle started with M61/M62 was interrupted
60 - M61/M62 长工作台交换执行中断 - Press NC start key to continue the alternating table cycle - Press internal stop soft key to interrupt the alternating table cycle - 按压程序执行键继续执行长工作台交换 - 按压程序中断停止执行长工作台交换 061 Enable table 1 ! 061 启动 1 号工作台 ! - M61 starts the NC processing on page 1 (left) but the release key
61 (probe) has not been pressed - M61 已经启动但释放键尚未启动 - Press the key Alternating table mode on page 1 (left) - 在第 1 页按压长工作台模式启动 062 Enable table 2 ! 062 启动 2 号工作台 ! - M62 starts the NC processing on page 2 (right) but the release key
62 (probe) has not been pressed - M62 已经启动但释放键尚未启动 - Press the key Alternating table mode on page 2 (right) - 在第 2 页按压长工作台模式启动 063 Alternating table not active 063 交替工作台未启动 - M61 or M62 call the alternating table cycle although is has not
63 been activated (soft key or sensor dividing wall) - M61 或 M62 已经执行但软键或分隔版传感器 - Activate the alternating operation by means of soft key or mounted dividing wall - 使用软键启动长工作台模式或安装分隔板 064 Alternating table X position 064 交替工作台 x 轴位置 - When trying to select the alternating table operation, the X axis
64 was in the range of the dividing wall - 使用长工作台模式时,X 轴位置在分隔板位置 - Traverse the X axis from the middle in direction table 1/2 - X 轴位置需超过工作台一半 065 Pallet change basic position 065 交换工作台基本位置异常 - Pallet change interrupted - Error during pallet change - 交换工作台交换中断
65 - 交换工作台交换期间故障 - Move the pallet changer to its' 'home' position by means of the service function (Help) in Manual mode. - Test the inputs - 在手动模式下,使交换工作台回到正常位置 - 测试输入点 066 Pallet change timeout 066 交换工作台交换时间过长 - Timeout during pallet change - Interruption of pallet change
66 - 交换工作台交换时间过长 - 旋转工作台交换中中断 - Press NC start key to continue the pallet change - Press internal stop soft key to stop the pallet change - 压程序启动继续旋转工作台的交换 - 压内部停止软键去停止旋转工作台的交换 067 Pallet changer load guard open! 067 交换工作台的门打开!
67 - Pallet changer loading guard open - 交换工作台的门打开 - Close the Pallet changer loading guard - 关闭交换工作台的上下工件门 068 Workpiece not clamped ! 068 工件未夹持! - Pallet change interrupted - Workiece unclamped - Sensors or cables defective
68 - 交换工作台交换中断 - 工件松开 - 传感器或电线损坏 - Press the key "Workpiece clamping" - Check the sensors - 按压"工件夹紧"键 - 检查传感器 069 3D head timeout 069 3D 头动作时间过长
69 - Timeout during 3D head positioning - Interruption of 3D head positioning - 3D 头定位时间过长 - 中断 3D 头定位 - NC start key to continue the 3D head positioning - Internal stop soft key to stop the 3D head positioning - Service menu 3D head in manual mode - 按压程序启动键继续 3D 头定位 - 按压中断内部程序执行中断 3D 头定位 - 手动模式中执行 3D 头服务模式故障排除 070 3D head set reference 070 3D 头设定原点 - 3D head reference settings not yet made
70 - 3D 头原点设定不是 - Set reference on service menu 3D head according to the axes position - 3D 头服务模式使用轴定位设定原点 071 3D head G range 1 necessary ! 071 3D 头档位须回到低档!
71 - 3D head positioning is possible only in gear range 1 - 3D 头定位必须在低档位 - Select spindle rpm on 1st gear range TOOL CALL Sxxx - 适用 Tool call SXXX 定义主轴转速在低档位 072 Insert spindle S2 072 装入 S2 主轴
72 - M42 has been called to insert spindle S2 - M42 被执行以装入 S2 - Insert spindle S2 and press NC start key to continue - 装入主轴 S2 并按 NC start 键继续 073 Remove spindle S2 073 移除 S2 主轴
73 - M41 has been called to remove spindle S2 - M41 被执行以移除主轴 S2 - Remove spindle S2 and press NC start key to continue - 移除主轴 S2 并按 NC start 键继续 074 Tool Call from wrong magazine
74 074 从错误的刀库呼叫刀具 - A Tool has been called, which cannot be changed into the current spindle S1/S2. - 刀具呼叫无法从现有主轴 S1/S2 被更换. - Change NC program. - 修改 NC 程序. 075 预留
75 Reserved
076 PLC 9255 - Line: %d - W1022: %d
File: %s
76 PLC 模块 %d - 行号: %d
档案: %s
- PLC module 9255 has been caused an error by reading a able
- Line: xxx -> Line number of the table the error occurred
76 - W1022: xxx -> error recognition - PLC 模块 9255 表格读取错误 - 行号: XXX -->表格中此行发生错误 - Please see also module description - Please contact the OEM - 请参考模块说明 - 请联络机械制造商 077 Commissioning active 077 机械调整模式启动中 - The option "commissioning" has been set in the configuration of machine parameter/MP Config. Several monitoring functions are
77 disabled. - - Information only - 在机械参数/ MP Config 中此选项"commissioning" 已经设定.多项监 控功能已经取消. - 仅为讯息提式 - When the machine is delivered (factory default setting) the option should be switched off after the commissioning has been ompleted. - 出厂前机台调整完成后须将此功能关闭 078 Function not active 078 功能未启动 - Function not executable
78 - Option not active - 此功能不能执行 - 此功能未开启 - Information only - 只是讯息 079 Marker one/zero modified 079 Marker 1/0 已修改
79 - Error in PLC program - PLC 程序错误 - Please inform OEM - 请通知 OEM 厂 080 Value not permissible 080 输入值无法写入 - Function can not be activated because the values are not in the
80 permissible data range. - 此功能无法启动,因为此值不是在允许的范围内. - Check FN19, M-function and modify values. - Check values for temperature- and axis-compensation - 检查 FN19,M-功能和修改值的大小 081 Monitoring working area off ! 081 工作区域监控取消! - CAUTION ! - Axis may collide
81 - Monitoring working area has been switched off by soft key or M32. - 注意 -轴向可能发生碰撞 - 监视工作区已经藉由功能键或 M32 被关闭 - Information only - 仅供提示讯息 082 Protected working area !
82 082 被保护的工作区域 ! - Axes are near to a collision point. - In automatic mode axes are stopped, if the distance to go exceeds a collision point. - 轴向在可能碰撞区域 - 如果移动位在碰撞区域，在自动模式轴向停止 - Information only - 仅供提示讯息 083 Emergency stop after END PGM 083 程序结束后紧急停止 - The switching off of the machine after the next END PGM block was
83 activated via user parameters - 程序执行完毕后机台自动关闭 - 此功能由用户参数启动 - Information only - 仅供提示讯息 084 Reference necessary 084 需做原点复归
84 - The reference operating mode is necessary to carry outFunction - 需执行原点复归 - Select the operating mode Reference via soft key - 手动模式中启动原点复归软键 085 Hirth axis initialize 085 离合轴初始化 - There has been an actual to nominal value transfer for an axis which should keep the nominal value as actual (e.g. hirth axes) - It is no longer guaranteed that the kinematics can be calculated
85 correctly. - 呼叫一把不能交换之刀具 - 例主轴 S1 启动 -> CR 在位置供给 HSC 主轴 S2 - After a positioning the initialisation of the hirth axes will be executed. - 修改表之位置 - 修改 CR Aufruf - 修改 NC 程序 086 Temperature compensation 086 温度补偿 - Error occurred with temperature compensation by means of Pt100 sensors - 使用 PT100 传感器执行温度补偿发生错误
86 - Observe the information regarding the error reason in the small PLC window - 从 PLC 小窗口中检查错误讯息 087 PLC stack not empty ! 087 PLC 推迭未清空 ! - Debug note for PLC programmers
87 - Data was pushed onto the stack and not pulled off. - PLC 编辑，除错提示 - 档案放入堆栈后未提出 - Change the PLC program - 修改 PLC 程序 088 I'm reading MP's ... 088 参数读取中..... - With the first PLC scan or after changes the machine parameters are read in order to adapt the PLC functions
88 - Only after termination of this process can the machine be started - 机械参数修改后第 1 次 PLC 扫描，以配合 PLC 功能 - 需结束此程序后机械才可启动 - Information only - 仅供提示讯息 089 M00 programmed stop 089 M00 程序中断 - Program interruption caused by M00
89 - Press NC start to continue - 程序使用 M00 中断 - 按压程序启动后继续 - Information only -仅供提示讯息 090 M01 conditional stop 090 M01 选择性停止 - Program interruption caused by M01
90 - Press NC start to continue - 使用 M01 中断程序 - 按压程序启动继续加工 - Information only - 仅供提示讯息 091 M03/M04 or M19/M20 necessary 091 需启动 M03/M04 或 M19/M20 - To move axes at machining feed rate, one of the mentioned M commands must be active - M31 switches off the function temporarily until the next END PGM - Function can be deselected permanently via MP
91 - 使用加工进给移动轴向，上述提到之 M 功能需启动 - 使用 M31 暂时关闭此功能，直到下次程序结束 - 此功能可使用机械参数启动或取消 - Press NC stop / TNC stop - Correct the NC program - 按压程序停止及程序内部停止 - 修改 NC 程序 092 M function not used 092 M 功能未使用 - Programmed M command is not supported by the PLC program
92 - 编辑之 M 功能不支持 PLC 程序 - Press NC stop / TNC stop - Correct NC program - 按压程序停止及控制器停止 - 修改 NC 程序 093 Feed/Rapid feed pot = 0% !
93 093 程序/快速进给旋钮为 0% ! - Program start with turned off feed/rapid feed rate potentiometer. - 程序启动，进给旋钮关闭 - Increase the feed rate on the corresponding potentiometer - 旋转旋钮增加进给 094 Function ok ! 094 功能正常 ! - The active step of a HELP file was carried out successfully
94 - All relevant sensors O.K. - 除错模式(HELP FILE)步骤执行完成 - 传感器状态正确 - Information only - 仅供提示讯息 095 Check machine parameter ! 095 检查机械参数! - The machine parameter setting is not supported by the PLC program
95 - 机械参数设定不支持 PLC 程序 - Change the machine parameter - Observe the information regarding the error reason in the small PLC window - 更改机械参数 - 从 PLC 小窗口中检查错误讯息 096 Simulation Maschine aktiv -> For testing only! 096 仿真模式启动中 -->仅供测试使用! - Simulation of machine function activated by means of control test unit, although due to the I/O assignment a real machine can be
96 presumed - 使用控制器测试平台除错功能 - 与实际机台 I/O 配置可能不同 - OEM.CFG: DEFINE CFG_Simulation = "inactive" - 编辑 config.def DEFINE CFG_Simulation = "inactive" 097 Submit/Spawn queue full 097 Submit/Spawn 队列已满
97 - More than 8 jobs have been sent to the submit orspawn queue - 超过 8 个任务送给了 submit 或 spawn 队列 - Please contact the OEM - 请联系 OEM 098 TNC programming station 098 TNC 程序仿真器 - TNC programming station selected (MP7210). - Axes and spindle are not controlled. - Caution ! If PLC is active (MP7210=1), machine functions on simulated axes and spindle positions can be started. - 选择 TNC 仿真器 (MP7210). - 不能控制伺服轴与主轴 - 注意 ! 若 PLC 启动选择 (MP7210=1), 仿真轴与主轴位置之机械功能 可以启动 Special functions key combination TExx0 - Keys [Ctrl] + S -> NC start - Keys [Ctrl] + X-> NC stop -Keys [Ctrl] + Cursor up-> axes plus
98 - Keys [Ctrl] + Cursor down-> axes minus - Keys [Alt] + X-> Emergency stop PC keyboard or mouse support possible - Keys [Shift]+[Ctrl]+[Alt]+1 -> vertical soft key 1 ... - Keys [Shift]+[Ctrl]+[Alt]+6 -> vertical soft key 6 特殊功能键结合 TExx0 - 按键 [Ctrl] + S -> NC start - 按键 [Ctrl] + X -> NC stop - 按键 [Ctrl] + Cursor up ->正轴向 - 按键 [Ctrl] + Cursor down ->负轴向 - 按键 [Alt] + X ->紧急停止计算机键盘或鼠标可以支持 - 按键 [Shift]+[Ctrl]+[Alt]+1 ->虚拟软键 1 ... - 按键 [Shift]+[Ctrl]+[Alt]+6 ->虚拟软键 6 099 Message in PLC window 099 有讯息在 PLC 窗口中 - Further notes are displayed in the PLC window
99 - 进一步讯息显示在 PLC 窗口 - Press CE to clear the display - Press CE to display the next information (if available) - 按压 CE 清除显示 - 按压 CE 显示另一个讯息(如果有其他讯息) 100 Logbook writing 100 历程数据写入异常 - Data cannot be written to logbook
100 - 数据无法写入历程纪录 - Too many submit jobs active - Create data buffer in PLC memory (PLC application) - 太多 submit jobs 启动 - PLC 内存中产生数据缓冲区(PLC 开发) 101 PLC Module %d(1) - W1022: %d %s 101 PLC 模块 %d(1) - W1022: %d %s - PLC module 9xxx was not executed successfully. - (1) -> the first PLC module error during the PLC cycle - PLC 模块 9XXX，产生错误
101 - (1) -->在 PLC 周期间 , 第 1 个 PLC 模块产生错误 - Additional information in line 2 - Please see also module description - Please contact the OEM - 进一步讯息参考第二行 - 请参考模块描述 - 传送讯息至 OEM 厂 102 PLC Module %d(2) - W1022: %d %s 102 PLC 模块 %d(2) - W1022: %d %s
102 - PLC module 9xxx was not executed successfully. - (2) -> the second PLC module error during the PLC cycle - PLC 模块 9XXX，产生错误 - (2) -->在 PLC 周期间 , 第 2 个 PLC 模块产生错误 - Additional information in line 2 - Please see also module description - Please contact the OEM - 进一步讯息参考第二行 - 请参考模块描述 - 传送讯息至 OEM 厂 103 PLC Module %d(3) - W1022: %d %s 103 PLC 模块 %d(3) - W1022: %d %s - PLC module 9xxx was not executed successfully. - (3) -> the third PLC module error during the PLC cycle - PLC 模块 9XXX，产生错误
103 - (3)-->在 PLC 周期间 , 第 3 个 PLC 模块产生错误 - Additional information in line 2 - Please see also module description - Please contact the OEM - 进一步讯息参考第二行 - 请参考模块描述 - 传送讯息至 OEM 厂 104 PLC Module %d(4) - W1022: %d %s 104 PLC 模块 %d(4) - W1022: %d %s - PLC module 9xxx was not executed successfully. - (4) -> the fourth PLC module error during the PLC cycle - PLC 模块 9XXX，产生错误
104 - (4) -->在 PLC 周期间 , 第 4 个 PLC 模块产生错误 - Additional information in line 2 - Please see also module description - Please contact the OEM - 进一步讯息参考第二行 - 请参考模块描述 - 传送讯息至 OEM 厂 105 Check MP data table
105 105 检查 MP date 表 - Error during reading PLC:\MP\MP_data.tab - 读取档案期间错误 PLC:\MP\MP_data.tab - Check values in PLC:\MP\MP_data.tab - If necessary update file from existing backup - 检查档案的值在 PLC:\MP\MP_data.tab - 可以从备份文件中作档案的更新 106 Check MP Config Table 106 检查 MP config 表 - Error during reading PLC:\MP\MP_config.tab
106 - 读取档案期间错误 PLC:\MP\MP_config.tab - Check values in PLC:\MP\MP_config.tab - If necessary update file from existing backup - 检查档案的值在 PLC:\MP\MP_config.tab - 可以从备份文件中作档案的更新 107 RSxxx data transfer PLC 107 RSxxx 数据传送到 PLC 异常 - Attempt to synchronize data transmission on serial interface - 在串行接口,同步数据的传送失败
107 - Switch on receiver - Check machine parameter MP5xxx of master and slave - Check cableconnection - 开启接收端 - 检查机械参数 MP5xxx - 检查传输线的接线 108 RSxxx buffer overflow 108 RSxxx 缓冲储存区溢位
108 - Internal message - 内部的讯息 - Please contact the OEM - 传送讯息至 OEM 厂 109 RSxxx transmit error
109 109 RS xxx 传输错误 - Error on serial interface RSxxx detected - 串行接口 RSxxx 检查发现错误 - Check the cable connection - Press CE key and try to reconnect - 检查传输线的接线 - 请按压 CE 键且试着从新联机 110 RSxxx receive error 110 RSxxx 接收错误 - Error on serial interface RSxxx detected
110 - 串行接口 RSxxx 检查发现错误 - Check the cable connection - Press CE key and try to reconnect - 检查传输线的接线 - 请按压 CE 键且试着从新联机 111 RSxxx not operational 111 RSxxx 无法操作 - Error on serial interface RSxxx detected
111 - 串行接口 RSxxx 检查发现错误 - Check the cable connection - Press CE key and try to reconnect - 检查传输线的接线 - 请按压 CE 键且试着从新联机 112 Table editor blocked 112 表的编辑被锁住 - There is a table already open. The MP- or Config file cannot be edited. - In operating mode "Traverse reference points" it is not possible to
112 start the table editor. - 表已被开启. MP 或 Config 档案无法被编辑. - 在"原点复归" 模式不能编辑表. - Please close the table (e.g. Tool table) and retry. - Please change to mode "Manual operation". - 请关闭表 (例刀具表) 并重试. - 请切换至 "手动操作"模式. 113 Warning! DCM not yet active Permit positioning of axis %d-%s 113 警告！DCM 未启动 容许定位轴向向 %d-%s - DCM only becomes active after referencing all axes. - To prevent the danger of a collision, the operator must check the current axes positions. - DCM 仅在所有轴向回原点后启动. - To 为防止碰撞的危险, 操作者务必检查现有轴向之位置. - NC Start key: Movement to a safe position is executed. Subsequently, the reference run of the following axes is started automatically (option). - NC Stop/Axis Direction keys: Automatic reference-run is aborted. The reference run must be performed manually (axis direction
113 keys). - NC Start 按键: 执行移动至安全位置. 其次, 以下轴向之原点复归将自动执行 (选配). - NC Stop/Axis 方向按键: 自动原点复归被取消. 原点复归必须手动执行 (轴方向按键). 114 Reference NC start disabled! -> Use axis direction keys 114 程序启动键执行原点复归取消 -->使用轴向移动键
114 - Automatic referencing with NC start was aborted. - Automatic referencing cannot be ensured (nonvolatile RAM area not yet initialized). - 程序启动键执行自动原点复归被取消. - 自动原点复归未被确认 (非挥发性的内存区域未初始化). - The reference run must be performed manually (axis direction keys). - 原点复归必须手动执行 (轴方向按键). 115 Reference timeout axis %d-%s 115 原点复归逾时 %d-%轴 - Axis not yet reached safe position - 轴向未到达安全位置 - NC Start key: The traverse to a safe position will be re-started. Subsequently, the reference run of the axes is startedautomatically (option).
115 - NC Stop/Axis Direction keys:Automatic reference-run is aborted. The reference run must be performed manually (axis direction keys). - NC Start 按键: 移动至安全位置将再开始一次.随后, 原点复归将自动开始 (选配). - NC Stop/Axis 方向按键: 自动原点复归被取消. 原点复归必须手动执行 (轴方向按键). 116 Plug/unplug additional axis 116 插入/拔除附加轴向
116 - To plug or unplug an additional axis the machine mustbe off. - 插入或拔除一附加轴向必须将机器关闭. - Power off the machine ! - 将机器关闭 ! 117 Axes compensation changed! 117 变更轴向补偿值!
117 - Factor for linear axes compensation X, Y or Z has been changed. - X, Y 或 Z 之轴向线性补偿因子已经变更 - only message -仅供提示讯息 118 IPC 61x0 clock monitoring
118 118 IPC 61X0 时序监控错误 - IPC61x0 interface is faultily (Watchdog) - Operation via IPC has been deactivated - IPC61X0 接口错误 (监控功能) - 关闭由 IPC 操作机台功能 - Try to reconnect by key - Check ethernet interface - 请尝试由按键重新链接 - 检查网络联机设定 119 Operation mode 2 119 第二操作模式 - Information only
119 - 仅为讯息提示 - Spindle speed max = S800 - Axes feed max = F2000 - 主轴最高转速 = S800 - 轴向进给 = F2000 120 Operation mode 3 120 第三操作模式 - Information only
120 - 仅为讯息提示 - Spindle speed max = S5000 - Axes feed max = F5000 - 主轴最高转速 = S5000 - 轴向进给 = F5000 121 Operation mode 4 121 第四操作模式 - Information only
121 - 仅为讯息提示 - Spindle speed max = S5000 - Axes feed max = F5000 - 主轴最高转速 = S5000 - 轴向进给 = F5000 122 EMERGENCY STOP test required
122 -> Time remaining: %s h 122 需进行紧急停止测试 -->剩余时间: %s h - The EMERGENCY STOP test of the equipment needs to be repeated. - No new NC program can be started.(NC start lock) - A brake test is performed together with the EMERGENCY STOP test. - 设备需重复进行紧急停止测试 - 未测试完成前,程序无法启动 - 紧急停止测试时将同时测试剎车功能 - After the main switch was switched off, an EMERGENCY STOP test is always run. - The test must be repeated after 168 hours; it starts automatically. Prerequisites: - Doors are closed - No running NC program - Axes and spindle are stopped - 关电重开后将进行紧急停止测试. - 每 168 个小时将自动要求进行测试. 测试前须求: - 安全门关闭 - 未执行程序 - 轴向及主轴停止 123 Key non-functional 123 按键功能无效 In this context the key has no function. e.g.
123 - handwheel mode for HR420/HR5xx not on TE keyboard selectable (use handwheel key) - 在此状态下,此按键没有功能 比如： - HR420/HR5xx 的手轮模式按钮不在 TE 键盘上而是在手轮上。 124 EnergyOpt -> Machine switched off 124 能量优化 ->机械关机 - Machine inactive - Axis and Spindle in position
124 - NC Program inactive - 机械未启动 - 轴向及主轴未移动 - NC 程序未启动 - Delite the error with the CE - Switch on the Machine orSwitch off EnergyOpt - 使用 CE 键清除错误 - 启动机械或关闭能源优化功能 125 EnergyOpt -> AUTOSTART / warmup program active 125 能量优化 ->自动启动 - The machine will be switch on at the specified time automatically by EnergyOpt.
125 - Dependent to the configuration the drives or rather the warmup program will started - Energyopt 会将机器在设定的时间到达时自动启动。 -依照设定，驱动装置或暖机程序也会启动。 - Press the emergancy stop button Or switch off EnergyOpt - 按紧急停止按钮 或关闭 EnergyOpt 126 TNC/IP Client 1 -> Connection Error 126 TCP/IP 从属端 1
126 ->联机错误 - Error while sending data from PLC via TCP/IP sockets. - Timeout. - Connection Error PLC -> Python. - Server not reachable. - Python process crashed. - PLC 透过 TCP/IP socket 传送数据时发生错误 - 时间过长 - PLC --> Python 联机错误 - Python 程序错误 - Please contact the OEM - 请联络机械制造商 127 TNC/IP Server -> Connection Error 127 TCP/IP 伺服端 ->联机错误 - Error while sending data from PLC via TCP/IP sockets. - Connection Error PLC -> Python.
127 - Client not reachable. - Python process crashed. - PLC 透过 TCP/IP socket 传送数据时发生错误 - PLC --> Python 联机错误 - 无法联机至 Client 端 - Python 程序错误 - Please contact the OEM - 请联络机械制造商 128 Error in python mask 128 Python mask 错误 - A python mask raised an error. - Python process terminated. - Memory allocation error. - Pytnon Mask 档产生错误
128 - Python 程序中断 - Please contact the OEM - 内存分配错误
- 请联络机械制造商
129 129 Error left softkey menu 129 左功能键选单错误
- The left softkey menu raised an error.
- Python process terminated.
- Memory allocation error.
- 左功能键选单引发了一个错误
- Python 进程终止
- 内存分配错误。
- Please contact the OEM
- 请联络机械制造商
130 TT449 battery low
130 TT449 电池电量过低
130 - TT449 battery voltage too low
- TT449 电池电量过低
- change battery
- 换新的电池
131 Spindle lubrication air oil alarm
131 主轴油气警报器
-Source air pressure too low
131 -Tube broke - 源头气压过低 - 管破裂 -Check source air pressure -Check tube - 检查源头空气压力 - 检查管路
132 Spindle lubriaction low level
132 主轴润滑油低油位
132 - Spindle lubrication oil not enough
- 主润轴润滑油不足
- Fill oil to tank.
- 油箱请补油
133 Chip conveyer motor overload
133 排削机马达超载
133 - Chip conveyor motor overload
- 排削机马达超载
- Check conveyor motor system and circuit loop
- 检查马达系统和电路回路
134 Screw motor overload
134 螺旋卷削马达超载
- Screw motor overload
134 - 螺旋卷削马达超载
- Check screw motor protect switch
- 检查螺旋卷削马达保护开关
135 135 Mist oil level low
135 油雾溢面过低
- Mist oil level low - 油雾溢面过低 - Check oil mist tank. - 检查油雾箱
136 Hydraulic pump overload
136 油压泵超载
136 - Hydraulic pump overload
- 油压泵超载
- Check Hydraulic pump system and circuit loop
- 检查的液压泵系统和电路循环
137 C.T.S. filter pressure too hight
137 CTS 过滤器压力过高
137 - CTS filter pressure too high
- CTS 过滤器压力过高
- Clean the CTS filter
- 检查 CTS 滤清器
138 A.T.S. oil tank level low
138 ATS 油箱油位低
138 - Air through spindle oil tank level low
- ATS 油箱油位低
- Check air through spindle oil tank level low
- 检查 ATS 油箱油位
139 C.T.S. tank low level
139 139 CTS 水箱低水位 - Cooler through spindle tank low level - CTS 水箱低水位 - Check cooler through spindle tank system and circuit system - 检查 CTS 系统和电路系统
140 Balance pump overload
140 平衡泵超载
140 - Balance pump overload
- 平衡泵超载
- Check balance pump system and circuit loop
- 检查平衡泵系统和电路系统
141 C.T.S. coolant missing
141 CTS 无切削液
141 - Cooler through spindle coolant missing
- CTS 无切削液
- Refill coolant to tank
- 请补充切削液
142 Coolant tank high level alarm
142 142 水箱高水位警报 - Coolant tank high level - 水箱高水位警报 - Check coolant tank system and circuit loop - 检查切削液系统和电路系统 143 Coolant low level alarm
143 水箱低水位警报
143 - Coolant low level alarm
- 水箱低水位警报
- Check coolant system and circuit loop
- 检查切削液系统和电路系统
144 Level sensor not ok
144 液位传感器不能确定
144 - Level sensor not ok
- 液位传感器不能确定
- Check level sensor
- 检查液位传感器
145 Coolant through spindle motor overload
145 145 主轴中心出水马达超载 - Coolant through spindle motor overload - 主轴中心出水马达超载 - Check coolant through spindle motor system and circuit loop - 检查主轴中心出水电机系统和电路回路
146 X1 Axis motor overtemperature
146 146 X1 轴马达温度过高
- Coolant tube was broke or coolant system is not normal
-Parameter is wrong
- 冷却液管或冷却系统不正常
- 参数不正确
- Check coolant tube loop and coolant system
-Check axis parameters is ok
- 检查冷却液管循环冷却系统
- 检查轴参数的确定
147 U1 Axis motor overtemperature
147 U1 轴马达温度过高
- Coolant tube was broke or coolant system is not normal
-Parameter is wrong
147 - 冷却液管或冷却系统不正常
- 参数不正确
- Check coolant tube loop and coolant system
-Check axis parameters is ok
- 检查冷却液管循环冷却系统
- 检查轴参数的确定
148 Y1 Axis motor overtemperature
148 Y1 轴马达温度过高
148 - Coolant tube was broke or coolant system is not normal -Parameter is wrong
- 冷却液管或冷却系统不正常
- 参数不正确
- Check coolant tube loop and coolant system -Check axis parameters is ok
- 检查冷却液管循环冷却系统
- 检查轴参数的确定
149 Z1 Axis motor overtemperature
149 Z1 轴马达温度过高
- Coolant tube was broke or coolant system is not normal
-Parameter is wrong
149 - 冷却液管或冷却系统不正常
- 参数不正确
- Check coolant tube loop and coolant system
-Check axis parameters is ok
- 检查冷却液管循环冷却系统
- 检查轴参数的确定
150 B1 Axis motor overtemperature
150 B1 轴马达温度过高
- Coolant tube was broke or coolant system is not normal
150 -Parameter is wrong
- 冷却液管或冷却系统不正常
- 参数不正确
- Check coolant tube loop and coolant system
-Check axis parameters is ok
- 检查冷却液管循环冷却系统
- 检查轴参数的确定
151 C1 Axis motor overtemperature
151 C1 轴马达温度过高
- Coolant tube was broke or coolant system is not normal
-Parameter is wrong
151 - 冷却液管或冷却系统不正常
- 参数不正确
- Check coolant tube loop and coolant system
-Check axis parameters is ok
- 检查冷却液管循环冷却系统
- 检查轴参数的确定
152 Emergency stop
152 紧急停止
- Emergency stop is additional action
152 - 紧急停止已动作
- Emergency stop is an additional action.Please Check the major
alarm message for fix.
- 紧急停止是一个额外的行动。请检查修复的主要报警消息。
153 AMP cooler alarm
153 153 AMP 冷却器报警
- Power supply overheat or AMP cool alarm
- 电源供应器过热或是 AMP 冷警报
- Please check power supply working correct and check AMP cooler
device ok.
- 请检查电源工作正确,并检查 AMP 冷却设备确定。
154 Axis cooler alarm
154 轴冷却警报
154 - Axis cooler system alarm
-轴冷却系统警报
- Check axis cooler system and circuit loop
- 请检查轴冷却系统和电源系统
155 Spindle cooler system alarm
155 主轴冷却系统报警
155 - Spindle cooler system alarm
-主轴冷却系统报警
- Check spindle cooler system and circuit loop
- 检查主轴冷却系统和电路回路
156 Axis motor cooler system overload
156 轴马达冷却器超载
156 - Axis motor cooler system overload
- 轴马达冷却系统超载
- Check axis motor cooler system and circuit loop
- 检查轴马达的冷却系统和电路回路
157 AMP cooler overload
157 AMP 冷却器超载
157 - AMP cooler overload
- AMP 冷却器超载
- Check AMP cooler and AMP protect device
- 检查 AMP 冷却器和 AMP 保护装置
158 Air Dryer overload
158 空气干燥机超载
158 - Air Drier overload
- 空气干燥机超载
- Check Air Drier and protect device
- 检查空气干燥器和保护装置
159 Spindle sub tank overload
159 主轴副箱超载
159 - Spindle sub tank overload
- 主轴副箱超载
- Check spindle sub tank and protect device
- 检查主轴副箱和保护装置
160 160 X Axis right brake air low
160 X 轴右制动气压低
- Source air pressure too low -Missing air in the loop - 源头气压过低 - 缺少空气循环 - Check source air wheather is enough -Check air loop is ok - 检查源头空气是否充足 - 检查空气循环“
161 X Axis left brake air low
161 X 轴左制动气压低
- Source air pressure too low
-Missing air in the loop
161 - 源头气压过低
- 缺少空气循环
- Check source air wheather is enough
-Check air loop is ok
- 检查源头空气是否充足
- 检查空气循环
162 Y Axis brake air low
162 Y 轴右制动气压低
- Source air pressure too low
162 -Missing air in the loop
- 源头气压过低
- 缺少空气循环
- Check source air wheather is enough
-Check air loop is ok
- 检查源头空气是否充足
- 检查空气循环
163 Z Axis brake air low
163 Z 轴制动气压低
- Source air pressure too low
-Missing air in the loop
163 - 源头气压过低
- 缺少空气循环
- Check source air wheather is enough
-Check air loop is ok
- 检查源头空气是否充足
- 检查空气循环
164 B axis unclamp alarm
164 B 轴松开报警
164 - B axis unclamp alarm
- B 轴松开报警
- Check a axis unclamp signal.
- 检查一个轴松开信号
165 C axis radial unclamp alarm
165 165 C 轴的径向松开报警
- C axis radial unclamp alarm
- C 轴的径向松开报警
- Check c axis radial unclamp signal.
- C 轴的径向松开信号
166 C axis axial unclamp alarm
166 C 轴的轴向松开报警
166 - C axis axial unclamp alarm
- C 轴的轴向松开报警
- Check c axis axial unclamp signal
-C 轴轴向松开信号
167 Tool magazine switch in manual mode
167 在手动模式下的刀库开关
167 - Tool magazine switch in manual mode
- 在手动模式下的刀库开关
- Information only
- 仅是信息
168 Magazine motor overload
168 刀库马达超载
168 - Magazine motor overload
- 刀库马达超载
- Check circuit loop and magazine rotation
- 检查回路和刀库旋转
169 Mist oil overload
169 喷雾油超载
169 - Mist oil overload
- 喷雾油超载
- Check mist oil tank and protect device
- 检查油雾的油箱和保护设备
- Check mist oil tank and protect device
170 - 检查油雾的油箱和保护设备
- Spindle cooler system overload
- 主轴冷却系统超载
- Check spindle cooler system and circuit loop
- 检查主轴冷却系统和电路回路
171 C.T.S. PAPER FILTER PUMP overload
171 CTS 纸袋过滤机泵浦超载
171 - Cooler through spindle paper filter pump overload
- CTS 纸袋过滤机泵浦超载
- Check Cooler through spindle paper filter pump and protect device
- 检查纸袋过滤机泵浦和保护装置
172 Air conditioner alarm
172 空调报警
172 - Air condition alarm
- 空调报警
- Check air condition system
- 检查空调系统
173 Spindle sub tank level low
173 主轴副箱水位低
- Spindle sub tank level low
173 - 主轴副箱水位低
- Fill oil to tank
- 油箱补油
174 Chip conveyor EMG
174 排屑机紧急停止
174 - Chip conveyor EMG.
- 排屑机紧急停止
- Release chip conveyor EMG.
- 松开排屑机紧急停止
175 Coolant motor overload
175 冷却液马达超载
175 - Coolant motor overload
- 冷却液马达超载
- Check coolant motor and circuit loop
- 检查冷却液马达及电路回路
176 Air conditioner alarm
176 空调异常
176 - Air conditioner alarm
- 空调异常
- Check air conditioning and protect device
- 检查空调和保护装置
177 Axis lubricant overload
177 177 轴润滑超载
- AXIS lubricant overload
- 轴润滑超载
- Check AXIS lubricant and protect device
- 检查轴的润滑剂和保护装置
178 Service mode
178 服务模式
178 - Service mode
- 服务模式
- Service mode
- 服务模式
179 Lubricant X1 pressure low
179 X1 润滑油压力过低
- Lubricttion X1 press low
179 - X1 润滑油压力过低
- Visual inspection for oil loss
-Electrical connection of pressure switch
- 目视检查油的损耗
- 电气连接的压力开关
180 Lubricttion X2 press low
180 180 X2 润滑油压力过低
- Lubricttion X2 press low
- X2 润滑油压力过低
- Visual inspection for oil loss -Electrical connection of pressure switch
- 目视检查油的损耗
- 电气连接的压力开关
181 Lubricttion YZ press low
181 YZ 润滑油压力过低
- Lubricttion YZ press low
181 - YZ 润滑油压力过低
- Visual inspection for oil loss
-Electrical connection of pressure switch
- 目视检查油的损耗
- 电气连接压力的开关
182 Heater exchange overload
182 热交换器超载
- Heater exchange overload
182 - 热交换器超载
- Check Heater exchange and protect device
- 检查热交换器和保护装置
183 Vacuum motor overload
183 183 真空马达超载
- Vacuum motor overload
- 真空马达超载
- Check Vacuum motor and protect device
- 检查真空马达保护装置
184 Spindle Lubrication overload
184 主轴润滑机超载
184 - Spindle lubricant overload
- 主轴润滑机超载
- Check Spindle lubricant and protect device
- 检查主轴润滑机和保护装置
185 Spindle lubrication low pressure
185 主轴润滑机压力过低
185 - Spindle lubricant low pressure
- 主轴润滑机压力过低
- Check Spindle lubricant and pressure device
- 检查主轴润滑机和压力装置
186 Spindle lubrication error
186 主轴润滑机错误
186 - Spindle sub lubrcation fill not ready
- 主轴副油箱未准备好
- Check lubrcation pipe
-Check lubrication level sensor
- 检查润滑管
- 检查润滑油液位检知器
187 C Axis Position is Warning
187 C 轴的位置是错误的
- C Axis Position is Warning
- C 轴的位置是错误的
187 - Check C Axis position. -Axis on end position C+(>240). -Axis on end position C-(<240). -Please Recovery C axis position.
- 检查 C 轴的位置。
- 轴结束位置 C +（> 240）。 - 轴结束位置 C -（<240）。
- 请恢复 C 轴的位置。
188 Machine feed hold
188 188 机床进给暂停
- Machine feed hold
- 机床进给暂停
189 Spindle back sensor not in position
189 主轴夹刀确认位置错误
189 - Spindle back sensor not in position
- 主轴夹刀确认位置错误
- Check spindle clamp piston back seneor
- 检查电气回路是否短路或断路
- 检查检知是否异常
190 Source voltage overload185
190 电压保护器过载
190 - Source voltage overload
- 电压保护器过载
- Please check Source voltage
- 检查入电电压是否异常
191 Hydraulic MAG Low pressure
191 刀库油压压力过低
- No pressure build-up in hydraulic system
- Pressure loss - leaky pipe work
- Pressure switch defective
-刀库油压压力过低
- Visual inspection for oil loss
191 - Electrical connection of pressure switch
- 检查润滑管
- 检查润滑油液位检知器
192 Spindle bearing overheat
192 192 主轴培林温度过高
- Coolant tube was broke or coolant system is not normal
- Parameter is wrong
-主轴培林温度过高
- Check coolant tube loop and coolant system
- Check axis parameters is ok
-检查温度检知是否异常
-检查主轴温度是否超过原厂出场值
193 C Axis limit +
193 C 轴过极限 +
193 - C Axis limit
- C 轴过极限 +
- Move out c axis limit
-请脱离极限位置
194 C Axis limit -
194 C 轴过极限 -
194 - C Axis limit
- C 轴过极限 -
- Move out c axis limit
- 请脱离极限位置
195 Chip clean motor overload
195 195 侧喷马达过载
- Chip clean motor overload
- 侧喷马达过载
- Check machine Oil skimmer motor
- 检查是否有短路或断路
- 检查线圈阻抗是否过高
200 ASDA magazine alarm
200 台达刀库马达报警
200 - Magazine inverter alarm
- 台达刀库马达报警
- Check magazine inverter alarm from LED
- 检查台达驱动器面板上 LED 提示报警进行排除
201 Oil skimmer overload
201 油水分离机过载
- Oil skimmer overload
201 - 油水分离机过载
- Check machine Oil skimmer motor
- 检查是否有短路或断路
- 检查线圈阻抗是否过高
202 ZF flow rate not enough
202 202 齿轮箱流量过低
- ZF flow rate not enough
- ZF 齿轮箱流量过低
- Check ZF flow rate
- 检查流量检知是否异常
- 检查流量阀门设定是否异常
- 检查油冷机是否异常
203 Head flow rate not enough
203 头部齿轮箱流量过低
- Head flow rate not enough
203 - 头部齿轮箱流量过低
- Check Head flow rate
- 检查流量检知是否异常
- 检查流量阀门设定是否异常
- 检查油冷机是否异常
204 ZF suction oil motor overload
204 ZF 抽油马达过载
- ZF suction oil motor overload
204 - ZF 抽油马达过载
- Check ZF suction oil motor breaker
- 检查是否有短路或断路
- 检查线圈阻抗是否过高
- 检查油管是否破裂
205 BC lubrication motor overload
205 BC 轴 抽油马达过载
- BC lubrication motor overload
205 - BC 轴抽油马达过载
- Check BC lubrication motor breaker
- 检查是否有短路或断路
- 检查线圈阻抗是否过高
- 检查油管是否破裂
206 SP lubrication motor overload
206 主轴抽油马达过载
- SP lubrication motor overload
206 - 主轴抽油马达过载
- Check SP lubrication motor breaker
- 检查是否有短路或断路
- 检查线圈阻抗是否过高
- 检查油管是否破裂
207 BC axis Tension pressure alarm
207 207 BC 轴 油压预压报警
- BC axis Tension pressure alarm
- BC 轴 油压预压报警
208 B axis limit +/-
208 B 轴过极限 +/-
- B axis limit +/-
208 - B 轴过极限 +/-
-依照下方提示是否为正或负方向
-使用极限解除,进行排除
209 arm motor overload
209 209 刀臂马达过载 - arm motor overload - 刀臂马达过载 - Check conveyer motor system and circuit loop - 检查刀臂马达回路是否短路